It is okay that more mass loading may increase resistance and therefore capacitance will be less. However, what should happen ideally when we increase mass loading?
If I use very less mass loading, will it give better results?
Dear Mohit Saraf,
what if you do the experiment and show us, please, the graph capacitance vs. "mass loading or thickness".
I have calculated specific capacitance of 200 F g-1. Now I wish to calculate Areal Capacitance. What is the formula? Electrodes: working Glassy carbon electrode of 3mm diameter (0.0707...
05 June 2019 2,442 5 View
Usually, high surface area and porosity are reported to be the primary reasons for good electrochemical sensing and supercapacitor performance. Please explain what exactly happens with high...
05 June 2019 5,261 6 View
Please give some details. Why it happens in particular for battery like electrodes?
05 June 2019 9,804 2 View
Kindly shed some light on it. In my case, the rGO alone is providing better supercapacitor properties than composite.
03 April 2019 9,197 4 View
Suppose, I want to make a composite of MOF and graphene. I wish to study the effect of relative content of participating constituents on the electrochemical properties. How to choose the ratio for...
05 June 2018 868 5 View
New journal of Wiley-VCH
31 December 2017 8,575 51 View
Can solid state thermolysis and calcination be called same at any particular conditions ?
07 August 2017 4,145 1 View
There are various methods to determine it. Can anyone show with example their suitable employed method ??
05 June 2017 4,953 1 View
I am trying one coordination polymer as electrode material on glassy carbon electrode. It is showing good stability. What can be the reason?
05 June 2017 4,520 7 View
I have observed higher values of supercapacitance of NRGO than rGO, which has better dispersion than rGO. But what can be the possible reason of higher supercapacitor performance? Has it something...
02 March 2017 655 2 View
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...
06 August 2024 3,176 0 View
How can I measure the thickness of thin film by Uv-Vis?
06 August 2024 7,810 3 View
Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...
05 August 2024 3,783 2 View
Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?
03 August 2024 7,035 3 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
I'm researching light sources and their UV emissions. I'm curious if a 50W, 7500K conventional LED lamp emits any UV light. I found that a 200W tungsten lamp can emit up to 1.5 mW/cm² at 350 nm....
31 July 2024 3,843 7 View
I need something like Camag's VisionCat software for photodocumentation of TLCs. Could you recommend something?
31 July 2024 8,415 1 View
Following curve related to Co0.6Mn0.4Fe2O4 Magnetic nanoparticles with extra phase a-Fe2O3. I will appreciate to help me to interpretation this spectroscopy, especially the blue line.
31 July 2024 9,140 2 View