How one can translate capacitance values to biasing voltage, specially in terms of varactor diode?

More Salman Arain's questions See All

What is the theorotical and practical meaning crossovers with respect to Couplers in microwave engineering?

What is the exact meaning of crossovers specifically with respect to couplers.

05 June 2015 2,624 3 View

Is there anyone, who is using ISOCAM software for creating milling or drilling data?

When I open my Gerber file to isocam it does not looks the same as my main design. Any suggestions and tips.

04 May 2015 5,940 0 View

Any good and relevant book or literature for understanding odd and even modes in microwave circuits?

Except saying, that in even modes there is a open circuit and in odd modes there is a short circuit. Is there any book or literature that can be used for best understanding about even and odd modes.

03 April 2015 2,365 12 View

What is a suitable way of converting a HFSS file into a gerber file for fabrication purpose?

What software or what tool is good to use for converting a HFSS file to a gerber file

02 March 2015 806 6 View

What can be the best position for putting the Radial stubs in the planer design for diode biasing?

We use radial stubs for the the biasing of diode as well. How we can locate the best position to include radial stub in the circuit design.

31 December 2014 6,503 7 View

How to include the effect of S2P data file in momentum simulation in ADS?

Can anyone knows how to include the effects of a diode s2p file in momentum. In the palette of (Lumped with artwork) there are 3 symbols of s2p block at the end. One is connector artwork, other is...

11 December 2014 8,264 4 View

Is it possible to simulate S2P data block in Momentum?

If we implement a diode or its equivalent or simple the resistor or capacitor data and put into a s2p file and the use that block with momentum. Will it be work with it or not in ADS

11 December 2014 6,598 7 View

How can we simulate momentum and also include the ports for lumped or active elements within momentum to include effects In ADS?

There is a way of co simulation but how can we add port for the resistor or capacitor? Which tool or palette box will be needed?

11 December 2014 470 2 View

How can I model a PIN diode in Momentum Simulation?

Can we directly model a PIN Diode or any other active device in Momentum ADS or do we have to import the active devices from some other softwares.

10 November 2014 9,443 6 View

How can one plot S parameters of PIN diode in ADS using only the data file of PIN diode?

What will be the procedure for plotting only the s parameters of the PIN diode in ADS by using the data file of S2P from the diode manufacturer.

10 November 2014 6,348 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

What's the role of IT & AI in Telecommunication Industry?

05 August 2024 8,264 3 View

What are some signs that an ECM is overfitting the Nyquist plot?

What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?

31 July 2024 7,425 0 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Terrorism, a natural inclination of all animal species?

There are many types of symbolic judgements. For example, when an Israeli pilot flattens the home of a Palestinian family (even if they are forewarned), it is natural for them to experience shock...

28 July 2024 2,610 1 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Vladimir Burtman

Hi Samman,

see chapter "3.2.2.1. Theoretical Background for the Capacitive Probe Measurements", page 193 in appended paper. Good luck Vlad

S.I.s. Hassan

I think use simple formula Q= CV ---> V= Q/C . Thus voltage inverse proportionally to Capacitance value.

Amipara Manilal D

Refer the data sheet of varacter diode used. Manufacturers provides voltage verses capacitance characteristic of varactor diode. Using the characteristic you can trtanslate the same

Salman Arain

Thanks sir, yesterday I went through that