How do you find out the most cited paper from Web of Science?

Finding most citated papers in a given topics by using Web of Science tool

05 June 2019 2,765 4 View

No title

08 September 2018 3,685 4 View

Either anionic or non-ionic detergent is suitable for preparing lysis buffer?

I am presently planning to do western blot. In addition, I am working H9C2 cell lines. So, I need to prepare sample from cell line. Before to start, I have to prepare lysis buffer. In this...

05 June 2018 5,779 5 View

What are the shelf-life and optimal storage conditions for cell culture media?

I am currently working with H9C2 cell lines. I prepared the complete growth media by using following: 1. DMEM 2. 10% FBS and 3. 1% PS Finally, I know media (DMEM) by itself is generally stable for...

05 June 2018 9,877 4 View

What is the optimal storage condition of Sodium fluoride (NaF)?

In lysis buffer, Sodium fluoride (NaF) act as a serine/threonine phosphatases inhibitor. I found different concentration as well as different storage condition depending on its application over...

05 June 2018 2,763 4 View

How to prepare the Fixer solution?

I need a complete protocol to prepare fixer solution for X-ray film development. Note: For western blot Enhanced chemiluminescence (ECL) detection method.

04 May 2018 9,812 0 View

How to know the cell H9C2 is fully differentiated?

31 December 2017 5,637 5 View

Best method for superoxide dismutase measurement ?

I am presently working with H9C2 cell. Now, I want to quantify superoxide dismutase enzyme after exposure of hypoxic condition to H9C2 cells. So, which methods should I have to use?

11 December 2017 8,789 1 View

How can I choose best methodology to determine apoptosis?

In particularly, I want to know what criteria should I have to consider before selection of a apoptosis methodology? In addition, I am presently working on Ischemic reperfusion induced apoptosis...

11 December 2017 6,257 2 View

Spectrophotometric Enzyme Assays?

At first, I need a complete protocol on it. Secondly, I want to know that, how much this assay effective in case of when I want to determine the antioxidant capability of irisin and melatonin...

11 December 2017 9,452 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How to reduce debris with neuron isolation?

Hi there, I'm isolating neurons from PND1 guinea pigs and have noticed a bit of debris in the early days (this is day 4 plated) and a lot of variability between plates. Current protocol is...

14 February 2021 3,692 4 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View