How much is the efficiency of high density polyethylene process?

More Talieh Rajabloo's questions See All

What is the relation between water mass flow rate and the width of a forced draft wet cooling tower?

What is the relation between water mass flow rate and the width of a forced draft wet cooling tower? Is there any rules (of thumbs) to determine the width of a wet forced draft cooling tower for...

23 January 2018 935 9 View

Any idea on the calculation of overall heat transfer coefficient?

What is the mean amount of overall heat transfer coefficient at circular finned tube air-coolers?(A rough estimate on amount of h at air-side can help) Can anyone send me some good references for...

19 September 2017 1,537 5 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

In passive sampling, can polymer-lipid partition coefficients be applied independent of environmental salinity?

For example, if low-density polyethylene (LDPE) is equilibrated with PCB contaminated marine and freshwater sediments, can LDPE-lipid partition coefficients be used to obtain equilibrium...

28 July 2024 263 1 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

VOC analysis on GCMS ?

Hi everyone, Can someone explain for me a method to inject VOC collected with Tedlar bag from pyrolysis process and transfer or inject into GCMS. Thanks

22 July 2024 6,398 1 View

Abdelkader BOUAZIZ

Dear Talieh Rajabloo, please check these documents. My Regards

10.1002/9781119159797.ch3

https://link.springer.com/article/10.1007/s11705-010-0558-x

https://doi.org/10.1002/0471238961.0809070811091919.a01.pub3

Md. Mahmud

Please follow this-

https://www.semanticscholar.org/paper/Improvements-in-Energy-Efficiency-of-Polyethylene-Quachio-Germiniani/d62859c40a7bc44b1afae43c95b6a3efe5e98da5

Talieh Rajabloo

Thanks Abdelkader BOUAZIZ and Md. Mahmud