How I can simulate Quantum-well solar cells QWSC using silvaco?

More Idris Bouchama's questions See All

Should I use higher centrifuge speed or my polymerization actually did not work?

One of my sample (NIPs-non-imprinted polymer) couldn't settling down after centrifugation (4000 rpm). Might be due to very fine particles. So what I did, I let the samples to evaporate under fume...

06 December 2020 3,344 3 View

What can explain the high desorption percentage when the desorbent is NaOH on a material that has adsorbed an anionic dye ?

Good morning to all of you Please, I need some help, After the adsorption of an anionic dye by an activated carbon at acidic pH, I studied the desorption phenomenon using NaOH, H2O and H2SO4 as...

18 April 2020 2,592 5 View

How does the current flow in the tunnel junction of dual-junction solar cells?

The dual-junction solar cell composed of two sub-cells would achieve a better conversion efficiencies, but how does the current flow in the tunnel junction P++/n++ withou current loss?

12 April 2020 3,573 6 View

What's the best way to connect two solar cells in series?

We can connect CIGS/Pyrovskyte solar cells with several ways to form tandem solar cell. But what's the best one of them? . thank you.

08 April 2020 7,662 3 View

What's the best way to reduce the carrier recombination at the back contact of solar cells?

P-type absorber material, an n-type material is mandatory for creating a good p-n junction. The heterojunction Absorber/Buffer cell requires a transparent conducting oxide (TCO) layer at the front...

05 April 2020 7,047 4 View

How can help me about the real parameters for Perovskite thin film?

I would like to simulate a typical perovskite solar cell. I have found a lot of references for perovskite parameter values in literature. Does anyone have any reference so that I can get values...

02 April 2020 1,777 6 View

Can you tell me about the characterization methods to determine defects levels in the gap energy?

It's very important to determine the defects levels that impact on the solar cell performances, especially in the absorber part. We would like to know also the origin of this defects and their...

21 March 2020 4,938 7 View

How can I model & simulate quantum dote thin films using CASTEP with different tail parameters?

A QDSC solar cell design that uses quantum dots as the absorbing photovoltaic material. It attempts to replace bulk materials such as Si, CIGS, CdTe ... etc. Quantum dots have bandgaps that are...

16 March 2020 1,986 4 View

I need to know the best method to deposit Cu2SnZnS4 (CZTS) nanowires for solar cells?

Due to containing expensive rare metals of In and Ga, CIGS chalcopyrite materials have still not been fabricated as thin film solar cells on a large scale. Fortunately, another chalcopyrite...

29 February 2020 5,424 5 View

I need help on generating constraint for the development of a computer program for train running diagram , what are the basis?

Intend to use c++ programming if am able to generate the constraint , also I will appreciate suggestions on better software to use for the achievement of this aim.

24 February 2020 1,040 3 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Zia Hameed

Actually i am working on solar plates to enhance the efficiency of Smart grid. But in your question you can use the modules and silivaca atlas for help and here is link which will be beneficial for you..this is same research as your question.

If you need any help i am available. Thanks.

https://www.researchgate.net/publication/312094823_Numerical_simulation_of_multi-quantum_well_solar_cells_GaAs_InAs_using_silvaco_atlas