How I can coat porous metal, oxides nanowires or nanoparticles in the channels of 0.3 micrometer width and 0.5 micrometer depth????

Sandesh Chougule Patil @Sandesh_Chougule_Patil

05 May 2017 1 7K Report

suggest method of coating...

Dear Sandesh,

The question is interesting. From my point of view, you can coat by dip coating method or cavitation technique to get uniformity. However, you have to go Hit and Trial method to optimise the system.

https://www.ncbi.nlm.nih.gov/pmc/articles/PMC2898898/

https://link.springer.com/article/10.1007/s11947-008-0150-2

Badges
Science topic

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Why can't we get on top of this incubator infection (fungal)?

We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...

02 July 2024 6,375 2 View

How to load Remedesivir drug into mesoporous nanoparticles?

Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...

01 July 2024 889 3 View