How hydrophobic nature of surface affect adherence of Natural assemblage? Specifically at marine environment?

10 October 2017 0 3K Report

#Marine Coating. #adherence of phytoplankton to hydrophobic and hydrophilic substrates.

Badges
Science topic

More Sham ashok Patil's questions See All

Can we determine the reduction of Cu with help of UV-Vis spectrophotometer?

I have got many references suggesting to use Atomic adsorption spectrophotometer, and one for detection of reduction in lead conc. by uv-vis spectrophotometer through calibration curve.

31 December 2012 6,755 3 View

How to determine the concentration of PAH (Petroleum Aromatic Hydrocarbon) in oil contaminated soil?

I am working on Phytoremediation of Aromatic hydrocarbon. Trying to reduce the TPH being more specific PAH from soil.

11 December 2012 3,672 7 View

i am preparing buffer for RBC lysis, using following chemicals NH4cl : 8.0 gm NaCo3 : 1.0 gm EDTA : 0.1 gm in 100 ml water Sir, i want know the...

i am preparing buffer for RBC lysis, using following chemicals NH4cl : 8.0 gm NaCo3 : 1.0 gm EDTA : 0.1 gm in 100 ml water Sir, i want know the role of each one of these chemicals? will i...

01 February 2012 915 12 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Interpreting ATR-FTIR Spectra for Microplastics Research?

Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...

18 July 2024 7,258 3 View

How to decrease hydrophobicity of Ni-foam?

As, my studies are related to water adsorption, the substrates should be hydrophilic in nature. Ni-foam being hydrophobic in nature, the results are not as expected as in literature. Hence i...

14 July 2024 8,847 4 View

What is this animal ?

In saw this creature during a cable laying operation at 20km off the coast of Timor Leste on the timor sea at a depth of 1200 m.

14 July 2024 4,715 1 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View