What is the best method to conduct a meta analysis?

Dear Colleagues: For those of you who have conducted a couple of meta analyses, do you agree with these steps? What is the best method of extracting the data from the chosen studies? Formulate...

26 October 2020 1,539 6 View

What's the best way to contact you?

I'm working with some folks involved in the Herstory Project - I think they would be interested. [email protected] Thanks.

09 December 2018 3,461 3 View

I'm working with some folks involved in the Herstory Project - I think they would be interested. What's the best way to contact you?

[email protected] Thanks.

09 December 2018 4,784 2 View

People who have successfully cultured E14 mESC (feeder free)- what FBS catalog and lot number did you use?

05 June 2016 8,265 3 View

Can Copper(I) and Copper(II) Alkoxides of such type be synthesised?

Application of Copper(I) and Copper(II) are more in Nanostructured applications

09 October 2014 8,709 2 View

Steps to calculate activation energy by coats & redfern method?

I'm a chemistry student and I'm researching the kinetic degradation of mixed plastic waste. I'm having trouble calculating the activation energy by the coats & Redfern method. The data that...

24 February 2021 974 1 View

Droplet PCR in plastic chips always result an unexpected band, any suggestion of possible contaminations and how to improve?

I am doing droplet based digital PCR inside plastic chips. I can get the correct band, but I also consistently get an unexpected band, slightly shorter. I attached a typical gel image here....

18 February 2021 6,618 2 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

How to measure the hardness for PLA & PHAs polymers?

Hello, I am a bit confused on whether to follow ASTM D785 (Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials) or ASTM D2240 (Standard Test Method for...

21 January 2021 7,487 4 View

Where can I find stress-strain data for steel to define plastic properties in Abaqus?

I am looking for stress-strain data for steel to input for the plastic properties in Abaqus. However I cannot find any literature or experimental data on the matter. If full data is not available...

15 January 2021 9,070 2 View

Hi, could anyone help me knowing which kind of Diamond blade would be better to cut thermoplastic composite?

The blade that could cut ceramics, or the one that could cut plastics and polymers?

06 January 2021 2,713 3 View

Which module is preferred in Ansys software to simulate shrinkages of plastic powder for the Injection Molding (IM) process?

I need to know the effect of shrinkage of plastic powder materials by simulation using Ansys or Simufact software.

21 December 2020 5,693 9 View

Blow extrusion of PLA with the HDPE non rotary die. Is it possible?

Hello, I managed to run a small blown extrusion line, head diameter 70mm / screw 45mm. The machine is to be used for extrusion of sleeves from 200 to 500mm wide. Unfortunately, I have a draw...

13 December 2020 2,824 5 View

Which are the quality parameters considered for injection molded plastic products? And which inspection tools are used for the same ?

Quality parameters and inspection tools may differ from product to product. Please write whichever you know.

10 December 2020 1,478 2 View

Will i need to define ductile damage parameters as well as yield stress vs plastic strain values for performing Fire-tensile test of CFRP/GFRP BARS?

Can someone please help me in this regard ... i have modelled a CFRP/GFRP( elastic and plastic properties together with temperature dependent -mass density, thermal conductivity and specific heat)...

03 December 2020 5,435 3 View