How do you plot error in COMSOL Multiphysics V5.2?

Md Badriadib Aldrin Suhaini @Md_Badriadib_Aldrin_Suhaini

03 March 2016 0 7K Report

While doing the simulation in COMSOL Multiphysics V5.2, I found that there were errors being plotted (for my case, it was from Convergence plot 1 and 2 I think).

I would like to get this graphs for my thesis. Do you know how I can plot these errors?

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More Md Badriadib Aldrin Suhaini's questions See All

Develop operating envelope?

how do you develop an operating envelope for a solar compressor? what data I need and how do I know the operating envelope would be "perfect"? I have never done anything on operating envelope,...

04 May 2017 6,541 1 View

How do you reflect on a book?

how do you reflect on a book? I usually just close the book and give some thoughts to it but i feel like its not effective way to reflect by just giving thoughts. What are your suggestions? How do...

07 August 2016 9,268 4 View

Can I thank the people who have helped and gave me answers to my questions?

I would like to say thank you to all of you who have helped me so far with my thesis on the movement and concentration of suspended particles in the nodal planes of an ultrasonic standing wave...

05 June 2016 8,799 1 View

How do I get an 80 mark and above on writing a dissertation/thesis project?

I have finished my literature review and I have finished the draft of my numerical simulation(or you could say my own project). What is left is to 'beautify' my dissertation more. How do I get a...

04 May 2016 3,600 2 View

Look into my acoustic pressure field, does it look like having an acoustic streaming?

Why is it that in the middle there are no standing wave field?How will the particles move when the standing wave field is only on the upper and lower of the cavity?

03 April 2016 4,757 5 View

Why are the particles concentrated in the nodal planes for only a period of time?

As you can see from the attached diagram, the particles are concentrated in the nodal planes at 0.008 s. But at 0.1s, the particles are not as concentrated in the nodal planes as at 0.008 s ( i.e....

03 April 2016 4,523 9 View

How much nitrogen is required for regenerating a vapour phased carbon bed adsorption?

I only know that for steam regeneration, I need 3 to 5 kg of steam per organic removed. But what about nitrogen regeneration? How much flow rate or mass is needed per organic removed?

03 April 2016 4,906 3 View

What can you deduce from my 1D plot graph of the mass fraction of suspended particles in a standing wave field?

The y-axis shows the mass fraction of the suspended particles and the x-axis shows the length of the cavity. When x = 0, that is to the left end wall of the cavity, when x = 21, that is at the...

03 April 2016 7,931 2 View

For the COMSOL simulation of particle manipulation using ultrasonic standing wave, why is the resonant freq. different at different mesh sizes?

I have attached two diagrams, one is for an extra-fine mesh and the other is for an extremely fine mesh. I am using PZT-4D and my suspended particles are polystyrene particles in water. The...

03 April 2016 4,662 3 View

Why are my 1D and 2D plot results look different [COMSOL, ultrasonic standing wave on suspended particles]?

As you can see from at 0.013 and 0.02s,the 2D plot graph does not show any changes but from the 1D plot graph, it shows changes. Why is that so? Both plot shows the changes to the mass fraction...

03 April 2016 9,112 2 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

May members post flyers about opportunities to present at a conference? If so, where to post?

May members post flyers about opportunities to present at a conferehttps://veraeducation.com/nce? If so, where to post for the Virginia Educational Research Association? https://veraeducation.com/

08 August 2024 4,585 1 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View