How do you do computational design of molecular imprinted polymers?

27 November 2014 1 9K Report

I need a computer program to form molecularly imprinted polymers and their design by using template molecules. Do you have any suggestions?

Manel del Valle

You can use SYBYL modelling, where you need to build your library of monomers.

Badges
Science topic

More Z. Onur Uygun's questions See All

What are some challenges and controversies in the process writing approach?

I am interested in learning more about the issues, challenges or controversies surrounding the process writing approach to teaching. Could anyone provide insight or experience regarding the...

13 April 2024 8,803 4 View

How do i use ResearchGate?

I would wish to know how I can get relevant research articles while doing literature review for my academic research

08 April 2024 3,358 1 View

What are your guesses about the mushroom-looking structure attached?

Dear researchers, what could be the formation mechanism of the structure that is tiny in size at the end of the first day in the electroless nickel plating waste solution, grows like a mushroom...

13 February 2024 4,601 4 View

Which solvents could be used to precipitate short peptides?

We synthesized a peptide made up of 7 amino acids. After cleaving the peptide with TFA, we tried to precipitate the peptide from cold ether. However, it seems like our peptide is somehow soluble...

08 August 2023 270 3 View

Cellulose reinforcement Lignocellulose film ?

I am preparing a lignocellulose film with cellulose nanocrystal additive using TFA as a solvent. My aim is to improve the stress values, but I haven't seen any improvement. I am having difficulty...

16 April 2023 7,083 0 View

What's the chemical reaction on the GO surface during the storage?

The GO/PES membrane was prepared with vacuum filtration method. The GO aqueous solution was filtrated with a PES ultrafiltration membrane. As a results, the GO/PES membrane was obtained, that the...

27 March 2023 5,494 0 View

Can be quality electroless copper applied on aluminum powders?

Hello Researchers, What is the availability of homogeneous electroless copper plating layer on aluminum powders? Can I get the opinions of the experts on this topic? Best regards.

29 December 2022 1,595 0 View

How can I remove AZ P4620 residues on metal patterned surface?

I masked chips using AZ P4620 positive resist. After hard baking, I cannot remove residues from the metal patterned surface. I tried PRS-3000, remover PG. I am going to try 1165 remover. Can you...

09 May 2022 5,302 0 View

How to remove resist AZP4620 without damaging the metal layer?

I got hard-baked resist residuals (AZP4620) on small chips. I need to remove all residuals without damaging the metal layer. I used PRS-3000, TCE & acetone bath. None of them worked to wipe...

26 April 2022 1,853 0 View

Would Hyaluronic Acid be good choice as a ligand for using in Mesoporous Silica Nanoparticles for breast cancer treatment by PhotoDynamic Therapy?

We are trying to design Mesoporous Silica Nanoparticles for breast cancer treatment by PhotoDynamic Therapy. And we are challenging with a question that Which ligand should we add onto the...

24 April 2022 1,443 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Are there instances where molecules with larger molecular weights exhibit greater mobility than those with smaller molecular weights?

Hi, I know that low molecular weight (MW) molecules generally tend to have higher mobility, while high molecular weight molecules tend to have lower mobility. However, in my experimental...

06 August 2024 1,495 2 View

For an in-vitro drug release study, what molecular weight cut-off (MWCO) dialysis bag is required for a 117 kDa protein?

kindly reply me. Thanking you in advance.

05 August 2024 7,727 4 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View