How do we extract the sectional forces in any solid sections in each time increment in ABAQUS?

08 August 2017 0 4K Report

I am trying to obtain the bolt forces in the end plate steel bolted connections after the monotonic and cyclic analysis.Perhaps, it is done using the free body cut but I could not work it out.

Badges
Science topic

More Bimal Bhandari's questions See All

Can we model the Masonry system with steel plates or other interventions( timber, rc jackets etc) in SAP2000?

I am modeling the Masonry building in SAP 2000 as a solid element. I have modeled the interventions such as Steel plates as a linear element over the solid masonry element.And to some extent the...

04 May 2018 6,618 4 View

Restart error in ABAQUS -"Amplitude curve with name abc has been defined previously.This amplitude cannot be redefined".How do we solve this error?

Modeling and analysis of steel connections for time history analysis.

08 September 2017 7,082 5 View

How do we determine the kinematic hardening parameters to input in ABAQUS?

I am modeling the steel connections in ABAQUS to study its cyclic behavior.I have adopted combined hardening model for which it requires kinematic hardening parameter,C1,Gamma 1 etc.

05 June 2017 3,383 7 View

How to solve the ABAQUS ERROR " TOO many attempts made for this increment" ?

I am analysing the steel end plate connections in ABAQUS.I have used surface-surface contact formulation and heaxahedral elements for meshing.And my increment = 50 Initial increment = 0.1 Minimum...

05 June 2017 6,620 12 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Microtome tissue sectioning - How to prevent chatter of paraffin tissue specimen sections?

Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...

06 August 2024 666 4 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View