How do I simulate and analyze the switching surges produced by different type switchgear on EMTP??

Siphamandla Rubushe @Siphamandla_Rubushe

04 April 2018 1 2K Report

I want to see the difference in magnitude and waveform produced by different switching technologies (oil, air, vacuum and sf6). I want to view this on EMTP.

Omar Hazem MOHAMMED

Dear

Please see the attachements sites

Regards

http://yadda.icm.edu.pl/yadda/element/bwmeta1.element.baztech-e1e35890-959c-41d7-a08e-72855d688e08/c/36_2013__art0-31_comparison.pdf

http://electricenergyonline.com/show_article.php?mag=113&article=948

https://onlinelibrary.wiley.com/doi/pdf/10.1002/%28SICI%291520-6416%2820000130%29130%3A2%3C40%3A%3AAID-EEJ6%3E3.0.CO%3B2-1

https://hrcak.srce.hr/file/116645

Badges
Science topic

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

How the wettability of rock sample can be changed by ageing in pure hydrocarbon oils only?

I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...

27 February 2021 5,383 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

How to remove compound ( Europium complex ) from paraffin oil?

How can I remove my compound from paraffin oil? Mistakenly my compound fell in an oil. Compound = Europium complex

22 February 2021 5,667 2 View

When I mix oil and NaOH solution, Why solid layer in the surface is formed?

During my trial for lubricant oil re-refinery process, I use NaOH as coagulant agent. After overnight of gravity settling, a solid layer in the surface was form. what product is that? since the...

22 February 2021 2,116 4 View