How do I print variables from .tcl file in .cc file?

08 June 2015 0 10K Report

I'm trying to print the coordinate x and y of the beacon nodes in wireless sensor network topology I created in ns2? Is there anyway I can access the .tcl file variables in .cc?

I'm also trying to print node id from .tcl file through .cc file. Any help in this regard would be greatly appreciated.

Badges
Science topic

More Nazish Tahir's questions See All

How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What is the best way to track bird migration?

Migratory birds are globally scattered. What should be the ways to track them? Except ARGOS. Elaborate.

25 January 2021 2,355 4 View

How i can reduce the number of atoms using Vesta ?

I'm a new Vesta learner, I have downloaded cif of Ch3Nh3PbI3. Total number of atom in chemical formula for Ch3Nh3PbI3 is 12. But when i convert this cif to poscar file using Vesta, total number of...

14 January 2021 5,733 11 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

How to calculate the replacement cost of battery?

As battery needs to be replaced after the specific charge and discharge cycles mentioned in the datasheet. If we have the time series data of battery power and energy capacity, then how can we...

01 December 2020 3,433 3 View

Can anyone please elaborate the relationship between charge and discharge cycles and battery lifetime?

I am designing the optimal HESS capacity for the renewable system. I have to select the cutoff frequency of low pass filter to divide the low and high-frequency components. charge and discharge...

05 November 2020 8,397 3 View

How to select the frequency range in MATLAB Wavelet toolbox?

I have a continuous, time-domain noisy signal and want to decompose into low-frequency (LF) and high-frequency(HF) components using Wavelet Toolbox. But, I am unable to select the frequency range....

29 October 2020 5,219 5 View

How can I retrieve information of viruses reported from a particular region/country ?

Dear All, Can anyone please guide me on how to get information (sequences) of plant/animal viruses from a specific region ? Looking up the published literature is one way but its time-consuming,...

19 October 2020 3,958 1 View

How to remove unedited version of the manuscripts from research gate?

Our manuscript was published ahead of print. The edited and revised version is now available. How do I remove the old version of the manuscript from the research gate?

01 February 2021 5,965 1 View

How to give port for printed log periodic dipole array antenna in CST?

PLPDA have radiating element on both sides of the substrate. so how to apply port. i have attached the figure below.

03 January 2021 4,005 6 View

I want to design a printed log periodic dipole array antenna on only one side of the substrate. is this acceptable one ?

actually for PLPDA, it is designed on both sides of the substrate for providing 180 degree phase shift between the elements

28 December 2020 3,148 3 View

How can I find my publication with the highest citation rate?

How can I find my publication with the highest citation rate in Research Gate? Is there a list of my publications? How can I print the list?

23 December 2020 8,476 12 View

Is there any database of UK based advertisements? I am specifically looking for anti-counterfeiting ads. Any suggestion?

I am looking for print/tv/social media/outdoor anti-counterfeiting advertisements targeted to British consumers.

23 November 2020 7,950 2 View

Bio-intensive cropping systems can reduce the environmental foot print?

The adoption of bio-intensive cropping systems has the potential to reduce environmental footprints without compromising the economic gain per unit of resources.

12 October 2020 2,625 7 View

Tcl script in VMD?

Using a VMD script written by me (MOisoall.tcl) I try to visualize the behavior of HOMO in the course of an inversion of ammonia (Fig. 1), but the VMD script does not work correctly (Fig. 2)....

11 October 2020 2,310 2 View

Post-processing technique on machined and printed pmma?

Hi everyone, i'm currently searching informations about the post-processing technique on machined pmma and printed pmma. I'd really appreciate if you could provide any suggestion of...

11 October 2020 4,563 3 View

How to add a Storymap to get a DOI from ResearchGate?

How can I add a storymap to research gate in order to get a DOI. It is a storymap so I don't have a pdf to upload. I can upload it as a preprint. As a preprint shouldn't I be able to ask for a...

10 October 2020 1,888 3 View

In Abaqus UAMP subroutine, how to write sensor values to a text file at every time increment?

Hi guys, I am trying to export sensor values from within uamp subroutine to an existing .txt file at every time increment. The simulation is running without errors but the sensor data are not...

09 October 2020 8,821 2 View