How do I get data from wind turbine operation in ice conditions that I want to use for the FAST simulator?

More Reza Barati-Boldaji's questions See All

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to model Type 1 collagen structure for finite element analysis ?

I have started a project in which stress distribution in Type 1-collagen scaffold is to be modelled. I am thinking of using finite element analysis to model the structure and the loading...

07 February 2021 5,487 3 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

How can I model a vacuum region between a concentric tube in Ansys fluent?

I am modeling a double pipe (concentric tube) in Ansys Fluent. The center tube contains nanofluid, and the region between the pipes is a vacuum zone. The outer tube is used for reducing convection...

22 January 2021 2,781 3 View

Howmuch time can we rely on the total igE test result for determining omalizumab dosing ?

there is a patient who has underwent a total igE test 1 month ago. can we rely on the results and determine omalizamab dosing? or the new test should be performed?

11 January 2021 253 2 View

What type of plants is better to work in gene regulation control project ?

I Interested in to work in gene network modeling thus I need to know what is future of gene network modeling in agriculture thanks

04 January 2021 6,527 3 View

Is it possible to culture several cell lines in the same plate/dish/flask with complete cell separation?

I'm trying to screen the effect of a toxic agent. I need to see its effect on a few different cell lines with different degrees of resistance to this compound. I would like to possibly culture...

31 December 2020 5,740 3 View

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 2,109 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Adrian Gambier

Please, contact Wojciech Popko

https://www.linkedin.com/in/wojciech-popko-97b142b/?locale=de_DE

See for example: Interfacing of ice load simulation tools for cylindrical and conical structure with OneWind simulation tool for offshore wind turbines. Jun 2013. Proceedings of the 22nd International Conference on Port and Ocean Engineering under Arctic Conditions (POAC), Espoo, Finland

He also works in several projects about wind turbines under ice conditions.

Reza Barati-Boldaji

Thank you for introducing

Jakub Jurasz

Hello,

You can also try to contact with Prof. Andrew Kusiak. He is doing some intensive research on wind turbine failures and I guess he is advocating data sharing. He is at RG.

Best,

Jakub