How do I determine a reaction is mass transfer dependent or kinetics dependent for gas-solid reaction?

More Hassan Mirzaei's questions See All

How can i obtain sodium from sodium hydroxide?

I want extract of sodium from sodium hydroxide instead of using metalic sodium.

05 June 2017 6,354 3 View

How can I perform scale-up of a chemical reactor for gas/solid reaction?

i need scale up for PFR and batch reactor.

01 February 2017 4,497 0 View

How to choose important data and eliminate unnecessary ones?

How can we ensure the accuracy and reliability of the extracted data? Data extraction for process and utility systems for Pinch analysis study.

04 May 2014 8,752 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Marco Antonio Utrera Martines

good paper

Hassan Mirzaei

Dear Milad

thanks for your answer.

Jerry Decker

An increase of agitation, turbulence, or velocity will change the mass transfer but not alter the kinetics much.

Dear Jerry

Thanks for your explanation.

Mikhail Aleksandrovich Kuzin

Mass transfer and kinetic see follow links (gas - solid)

https://www.researchgate.net/deref/http%3A%2F%2Ftrace.tennessee.edu%2Futk_graddiss%2F1744

Article Kinetic modeling study of a voloxidation for the production ...

Article A semi-empirical model for the air oxidation kinetics of UO 2

Article Oxidation Mechanism of Copper at 623-1073 K

Dear Mikhail

Thanks for your answer.