How did you find bearing current calculation of the inverter fed motor

C. Bharatiraja @C_Bharatiraja

06 June 2017 1 10K Report

Mohamed Benbouzid

You can have a look on the attached paper. there is also a procedure for measurement!!

Regards,

Mohamed

Badges
Science topic

More C. Bharatiraja's questions See All

Calculation of current idc

calculate the inverter current idc to model the DC link

05 June 2017 2,271 1 View

Inverter Dead time related to What?

05 June 2017 7,930 1 View

Any one pls guide me the , What is IEEE recommended value for grid connected inverter Voltage and current harmonics values

05 June 2017 288 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

In frequency domain alpha band(8-16hz), beta band(16-32hz), gamma band(32-64hz), sub-band(64-128hz) are same as LL,LH,HL,HH in wavelet decomposition?

I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...

23 February 2021 5,503 1 View

Suppose we have a banana seller cart consisting of 4 wheels, weighing about 300 kg. How much torque motors are needed to pull of push it electrically?

I am thinking of electrifying the street food carts while harvesting energy using solar panels on top.

22 February 2021 4,323 3 View

What should be the duration of exposure to simulated space environments with Rodents?

Hi, I am currently working on a pilot study to get some data related to the impact of long duration spaceflight to the microbiome and the immune system. I plan to use rats and simulate...

22 February 2021 592 1 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

Can you please suggest me how to convert EDF file into Mat file for EEG datasets?

Hi sir, 1.can you please suggest to me how to convert the EDF (European Data format) file into a Mat(Matlab) file for EEG datasets?. 2. Also suggest some publicly available EEG Motor Imagery...

15 February 2021 7,620 1 View

Is Genetic Algorithm usage for Motor Conception FEA optimization a good choice?

Hi RG community, Like the title shows ,i was wondering if choosing the GA for this kind of Optimizaiton is a good choice? For example we have a population of 100 (for 7-8 Optimization Variables),...

14 February 2021 1,160 7 View

How to interface ANSYS Maxwell and Matlab?

Dear All, I am working on electric motor design in Ansys Maxwell. I have written optimization code in MATLAB. I want to run this code in ANSYS MAXWELL and generate FEA results. Does anyone know...

10 February 2021 1,279 1 View