How could I find a manual for the OAPI application of SAP2000?

06 June 2015 0 1K Report

I want to test the capabilities that OAPI can offer by starting to learn how to communicate with SAP2000 commands through coding written either in Matlab or in Python.

Badges
Science topic

More George Bekas's questions See All

How can a rigid diaphram be modeled in OpenSees?

Can I model a diaphragm as multiple master-slave node, lines of code or should I specify the whole polygonal boundary at once?

11 December 2017 364 6 View

Is there any notion of effective moment of inertia used in analysis RC elements according to Eurocode 2?

When conducting finite element analysis according to the Eurocodes, is it sufficient to use the uncracked moment of inertia, or is there any notion for the effective moment of inertia alike the...

10 November 2017 5,067 6 View

Can Eurocode 6 be applied for RC walls?

I am searching for a detailed solved example of a shear wall that also have to resist an axial load (design should be compliant to Eurocodes).

10 November 2017 347 4 View

How do I check the structural capacity of an element in OpenSees?

I am trying to find through which combination of commands, I check if a particular cross section, has sufficient capacity or not, after the structural analysis. The structural analysis will...

10 November 2017 5,301 4 View

What are some examples of good conferences about Building Information Modeling?

Especially if it is combined with workshops.

09 October 2017 394 1 View

I am looking for a particular resource about the modeling of the load transfer from slabs to beams in a 3D FE analysis context. Any ideas?

E.g. fixed end moments, shear forces, etc.

09 October 2017 1,907 4 View

Is there an example where recurrent neural networks have been used for optimization purposes?

Would the modeling of a physical system that displays a dynamic behavior be benefited by the use of e.g. genetic algorithms in order for optimal temporal decisions to be determined?

09 October 2017 4,820 3 View

What is a sufficient sample for a recurrent neural network?

Is there any relevant theory and publications?

09 October 2017 6,008 3 View

What does this particular MATLAB code mean?

loads{k,1}=loads{k-1,1}+1; loads{k,2}='py';

09 October 2017 3,016 3 View

What is recource for the load distribution coefficients for one way and two way slabs according to the Pieper/Martens method?

E.g. tables etc.

09 October 2017 7,944 3 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Can anyone provide the Support vector regression code structure of LIBSVM MATLAB or python ?

Please, if Gaussian Parameter optimization is possible in this code structure

28 February 2021 278 3 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View