How could i design the negative resistance region of UJT?

syed taha Ahmed @Syed_Taha_Ahmed

10 October 2017 0 8K Report

UJT between values of Vp and Vv operates in negative resistance region how could i graph this slope with accuracy.

Vp is Peak voltage of UJT

Vv is valley voltage of UJT

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More syed taha Ahmed's questions See All

Why the alternator connected to grid didn't loose synchronizm in following condition?

Lets say the grid is at ideal frequency 50 hz then the large load is shut of due to which frequency increases beyond 50 which tends to rotate all turbines faster than their previous speed but at...

08 September 2019 300 2 View

Why there is no current flows between B1 and B2 in Uni Junction transistor with emitter open as both the bases are on n type region?

The doping of N type is done lightly so the resistances are high between B1 and B2 but with this high resistances why electrons do not flow between B1 and B2 as leakage current flows through B2...

09 October 2017 8,967 0 View

For a medium line model half shunt, the capacitance is lumped at each end of the transmission line. Why?

I want to know why the model behaviour is very close to original structure and why we dont lumoed capacitence only in one side. Put more than two capacitence lump on model.

04 May 2017 4,711 1 View

Why ping and tracert commands works for blocked sites but sometimes do not work for open sites?

Hey once i have run ping and tracert command to my university's website but it does not work then i run above two commands for blocked site in Pakistan it works perfectly well for those so what is...

08 September 2016 4,719 0 View

Why sound waves have analog waveform in books while it is longitudinal waves ?

In signal communication books we make sinusoidal waveform for a sound waves but why we did it we know that sound waves are transverse in nature ?

08 September 2016 6,919 0 View

Double integration for area or for volume?

Hello My question is this that sometimes we use double integration for calculating volume but in many cases like in cylindrical and spherical coordinates system we usually use it to calculate...

08 September 2016 4,531 0 View

Billing of electric motors?

Motor is inductive load so how does our electricity residential meters calculate the power consume by motor? Motor needs current to produce magnetic field so that current and voltage would be...

06 July 2016 9,786 8 View

Detuned Reactors usage in PFI devices?

What are Detuned Reactors and why they are used in Power Factor Correction devices.I have found in Schneider Electric website that that they are inductors which are use to control harmonics but...

06 July 2016 4,786 2 View

In the zero bias condition of diodes, why does the minority carrier in n type move to p type where holes are in excess?

Is it against the law of diffusion? holes and electron carriers

03 April 2015 6,878 4 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

How combine yolo with Faster R-CNN?

I want a model that is balanced with accuracy or speed, faster rcnn has high accuracy while yolo have fast speed. i am thinking to combine them to get a hybrid model to achieve both speed and accuracy

02 August 2024 3,104 0 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

What is the best way to drop a plasmid?

Please address the best way to drop a plasmid. Background: I have a "bait" plasmid resistant to kanamycin and a "prey" plasmid resistant to carbenicillin. After many rounds of streaking on...

25 July 2024 2,532 3 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

Is a reliability test necessary in my survey on translations?

Dear all, I gave 116 respondents 18 translated sentences and asked them to indicate their levels of acceptance of these translations on a five-point scale. Some translations result from strategies...

24 July 2024 8,245 5 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

How do we pick data for determination of Validation Acceptance Criteria?

Hello, colleagues! There is commenting open for new upcoming edition of USP 1033. Validation target acceptance criteria is now different from what it used to be and it doesn't include Cpm....

23 July 2024 7,292 3 View