How could be coupled matlab with COMSOL?

More Mahdi Alibeigi's questions See All

How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Is a Strong correlation between the Moderator variable and the dependent variable an issue for moderation model (model 1) in Hayes PROCESS?

In a typical moderation model with one moderator, is it a problem if the moderator and the dependent variable show a strong correlation (say 0.85)? What if a strong correlation exists between the...

27 January 2021 4,937 4 View

Which syringe filters (e.g., PTFE, MCE, PVDF, CA, PES, etc.) are the best to filter TBS/PBS buffer (pH 7.5-8.5) and glycine buffer (pH 2-3) solutions?

I intend to purify antibodies from serum using the affinity procedure, and I need to filter the binding (TBS/PBS) and elution (Glycine) buffers before applying them to my solution.

06 January 2021 5,769 3 View

Gear reduction for back-drivability of a motor?

Hi everyone, Does anyone know up to what reduction ratio of gear does a motor remain back-drivable? I want my robot to have safe interactions with the environment and other humans. Can you give a...

26 December 2020 7,142 3 View

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

How to assign initial stress to a coating in Abaqus?

Hello! I am trying to define/assign initial stress to a coating I modeled on a substrate. I defined the coating using "skin" function. I have tried "predefine filed" in load section. But it only...

10 December 2020 2,921 8 View

How to model a multilayer coating in ABAQUS?

Hello! I'm trying to model a multi-layer coating on a substrate in abaqus. The layers are homogenous and isotropic. My question is how should I approach the modeling? WHAT I'VE TRIED SO FAR: I...

09 December 2020 1,235 3 View

How can I calculate Nusselt number by using this equation (Nu = ht.gradTx * nx + ht.gradTy * ny + ht.gradTz * nz) step by step in COMSOL?

Calculate the Nusselt number using the COMSOL Program

09 December 2020 3,354 3 View

How to calculate sulfur loading of lithium -sulfur batteries using Li2S8 catholyte?

I am gonna use Li2S8 catholyte to introduce active material to cathode instead of using sulfur. May anybody kindly guide me about the way I can calculate the amount of sulfur (g/cm2) loaded on the...

07 December 2020 7,556 2 View

How to great data visualization and what example for it ?

i need explain data visualization and what type it and how great it by excel or other program > paper attached for help

30 November 2020 1,159 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Please. Could you help be in implementing Fractal Discrete Cosine Transform algorithm in Matlab?

I do need the Matlab code of Fractal Discrete Cosine Transform (FDCT). Can anyone who has already implement this code, help me with the implementation of this transform?

24 February 2021 5,602 2 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

Muhammad Ali

I suggest you follow : https://www.youtube.com/watch?v=sHOFmyHKFS0

https://www.comsol.com/video/livelink-matlab-demonstration

https://au.mathworks.com/products/connections/product_detail/comsol-multiphysics.html

Pawan Kumar

you can easily link MATLAB and comsol, please see the attached video link:

1. https://www.youtube.com/watch?v=dB6_yqQ-GPA&ab_channel=HighVoltageEngineeringbyMGNiasar

2. https://www.youtube.com/watch?v=p7MwR1nRgC0&ab_channel=AleksandarHaber

3. https://www.youtube.com/watch?v=sHOFmyHKFS0&ab_channel=GamaxLtd.