How can I access Model 25 in PROCESS for SPSS?

There are certain models in "Model Templates for PROCESS for SPSS and SAS" (e.g. Models 23 through 27) which are not accessible via PROCESS. Can anyone advise me how to get access to these...

13 January 2020 3,146 3 View

How do I interpret coefficients in regression with dummy dependent variable?

I am struggling with the interpretation of my coefficients. How do I interpret beta1 in this analysis? I estimate this equation by Linear Probability Method.

11 May 2018 7,444 1 View

How to interpret coefficient in estimation with dummy dependent variable?

11 May 2018 5,619 2 View

What importance is there to stating an ontology and epistemology as part of the method section in a journal paper?

Qualitative research method descriptions are likely to benefit from a clearly stated ontological and epistemological position. Yet, many authors do not state their position on either. Is there a...

22 January 2014 4,101 20 View

Verification of efficiency of RNA-interference

How can we verify/check up the effectiveness of RNA interference? (using molecular methods)? Thanks,

01 January 1970 8,236 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View