Is there any future prospect to generate usable amount of energy from various EM Fields available around us ?

Why only light and not other EM wave ?

31 December 2013 8,218 2 View

What is the best optimisation technique for electron device modeling?

Can I use GA, PSO, ANN or any other?

31 December 2013 3,847 2 View

Can we use graphene material in any type of solar cell design?

.

31 December 2013 5,777 3 View

What is the best opto-electronics device simulator available so far especially for all kinds of solar cells?

We know that there are so many TCADs and numerical device simulators such as Silcaco ATLAS, Synopsys SENTAURUS, PC1D etc. available today. Can anyone help me to choose the one that will serve the...

11 December 2013 3,718 1 View

What is the expected life span of Dye Sensitized Solar Cell (DSSC) panel?

Does it last longer than todays Crystalline Si solar cell panel? All these discussed cell should be of commercially available ones in market and not of experimental/laboratory type.

11 December 2013 9,318 1 View

What is the difference between vertically aligned and horizontally aligned p-i-n nanowire solar cell?

In terms of light coupling, photogeneration rate and efficiency.

11 December 2013 2,688 0 View

Can we import VHDL/VerilogHDL or SPICE model in MATLAB Simulink?

If there is possibility, then can we write/call the program directly inside simulink library file. Or is it necessary to install third party toolbox or add-on in order to allow it?

11 December 2013 8,396 1 View

How do i plot responsivity of Photodiode in ATLAS ?

I currently simulating a UV photo-detector using ZnO as primary material.I did all in silvaco TCAD Atlas code.I will be very thankful if anyone provide me the idea of the detailed code for...

01 January 1970 4,783 1 View

For RF performance analysis of FET, we need cut off frequency FT plot? Can someone help me to plot cut-off frequency of FET in ATLAS ?

I need this plot for my current project Graphene based FET for RF performance analysis

01 January 1970 6,209 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View