How to evaluate any policy or programme critically ?

From the design of the programme and its implementation level, it is important to understand its conceptual and exceutive level, so that one can know the philosphy behind the policy and programme...

01 February 2018 3,973 0 View

What you think about transition of Communicable diseases to Non- communicable diseases- Reality or Myth ?

08 September 2017 675 2 View

Why case reports are not published in most of the Journals?

07 August 2017 2,435 4 View

Can randomization in a clinical trial help in achieving balance in baseline characteristics?

Randomization is a cornerstone of any RCT and therefore needs to be understood carefully.

01 February 2017 1,471 0 View

Can we use e learning in public health teaching and how ?

11 December 2016 673 1 View

How we can study housing conditions and health ?

House is very essential for shelter, security and safety. If the housing condition is not according to the criteria, then it may cause negative impact on health, especially in Low socioeconomic...

07 August 2016 7,820 15 View

Which is the best strategy to prevent & control HIV/ AIDS, IEC activities or Treatment ?

AIDS is still a serious health problem. Multi pronged strategies are applied to prevent & control this infection. But it seems that more stress is given on the treatment aspect. What are your...

06 July 2016 6,070 22 View

What type of topics should be allotted to the students in Public Health for Thesis?

Mostly,topics allotted to the students for thesis work are of traditional type i.e., regarding knowledge, attitude and practice and cross sectional study to know the burden of the particular...

06 July 2016 8,395 1 View

Do you think peer education is best way to create awareness and behavior change?

In current scenario, most of the health problems are facing by one particular group of the population(peers).But If on one side, the peers are more prone to health problems especially lifestyles,...

31 December 2015 4,528 2 View

How we can address the problems of nutrition in the elderly population?

Elderly population is mostly vulnerable to the various nutritional problem, which is not only because of the physiological aging process, but also due to the lack of social support especially...

07 August 2015 3,571 22 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View