What is are the different classifications of a tool changer?

I have roamed the internet trying to see the different types of tool changers available but I found no definitive answers, could you kindly help me?

02 February 2021 5,036 1 View

How to calculate covariance of Expectation Maximization Clustering?

I am working with MatLab R2017a, I have to implement EM clustering. But I am stuck with initialization of covariance in it. I have to calculate covariance using the dataset which is comprised of...

25 December 2020 4,620 3 View

MatLab code for Expected Maximization clustering of n-Dimensional data?

I need matlab code for expected maximization clustering of n-Dimensional data. I have searched and found code related to 1-D and 2-D. Can someone refer the code for n-D .

22 December 2020 5,110 3 View

Where can I find papers related to microstructure of inconel alloy 800?

I need to define the microstructure of inconel 800, but I cannot find any literature related to it. Literature is about incoloy 800 mostly which is a bit different. Can anyone tell me if there...

07 December 2020 3,137 3 View

Which software application is best for Anova analysis?

I want to perform "ANOVA" analysis of three different vegetation indices. anyone know how can i perform and which application /software are suitable for this. Thank you in advance.

16 November 2020 2,599 4 View

How can I specify the parameters for nano creep?

Which parameters should I employ for nano creep testing of Titanium and Inconel alloys? Should I load it with a constant load rate or strain rate? What should be the maximum load? What should be...

29 October 2020 5,727 4 View

How to find the elastic work using nanoindentation load depth curves?

I am using work of indentation approach to find out the values of hardness of Ti and Inconel alloys using nanoindentation load-depth curves. I can find the formula for total work. Whereas for...

13 October 2020 2,778 5 View

How to measure the volume of hydrogel?

08 October 2020 2,745 9 View

Why nickel oxide nanoparticles do not have single band gap?

band gap for nickel oxide nanoparticles is 3.85 to 3.45 eV

23 September 2020 260 4 View

How to Determine LD50 of a test compound by Lorke's Method if your mice (mus musculus) dies at the lowest concetration i.e. 10mg/kg?

I have used Lorke's method of determining LD50 of my test drug. The lowest dose according to this method is 10mg/kg and my mice died at this dose within the 30 minutes of IP injection. Does that...

22 September 2020 9,959 3 View

Is there any research regarding how training and development is going to change in the era of Fourth Industrial Revolution?

As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...

01 March 2021 3,199 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Is anyone working on a project focused on immigrants/newcomers working in the hospitality industry and how they have been impacted by COVID?

The on-going Covid-19 pandemic has had devastating economic effects on many industries. However, few have suffered to the same extent as full-service restaurants. Numerous studies have shown that...

24 February 2021 9,496 4 View

What is the optimum time and temperature of blanching and pre-frying potato for frozen fries?

I am helping a local home industry for developing frozen fries from their local farm. I want to know what is the optimum blanching and pre-frying temperature and time for processing. Please also...

23 February 2021 1,616 5 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

What is the role of work experience in motivating high tech entrepreneurship in Aviation industry?

Related work experience plays a vital role in motivating the Entrepreneurship. But when we talk about high tech entrepreneurship in Aviation industry, we talk about very high investment and high...

22 February 2021 376 5 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View