How can use hetero-structure in tunneling FET for improvment the electrical charactristics?

More Reza Meshkin's questions See All

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to model Type 1 collagen structure for finite element analysis ?

I have started a project in which stress distribution in Type 1-collagen scaffold is to be modelled. I am thinking of using finite element analysis to model the structure and the loading...

07 February 2021 5,487 3 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

How can I model a vacuum region between a concentric tube in Ansys fluent?

I am modeling a double pipe (concentric tube) in Ansys Fluent. The center tube contains nanofluid, and the region between the pipes is a vacuum zone. The outer tube is used for reducing convection...

22 January 2021 2,781 3 View

What type of plants is better to work in gene regulation control project ?

I Interested in to work in gene network modeling thus I need to know what is future of gene network modeling in agriculture thanks

04 January 2021 6,527 3 View

Is it possible to culture several cell lines in the same plate/dish/flask with complete cell separation?

I'm trying to screen the effect of a toxic agent. I need to see its effect on a few different cell lines with different degrees of resistance to this compound. I would like to possibly culture...

31 December 2020 5,740 3 View

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 2,109 5 View

How to find the natural frequency of nonlinear model (hyperelastic materials) in ansys APDL?

I'm working on the FE analysis of nonlinear vibration of circular plate in ansys APDL. I considered the Mooney-Rivlin model of hyperelastic materials. So i want to know that how to find natural...

27 December 2020 8,696 2 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

How can I plot surface potential vs Gate voltage in Sentaurus TCAD?

Currently, I am working on a project in Sentaurus TCAD for which I required the plot of Surface Potential Vs Gate Voltage. Can anyone help me finding the simplest way or a different procedure for...

18 February 2021 1,213 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

Using SILVACO to design tandem organic solar cells?

Hi Can anyone please suggest me how can I study the parameters of solar cells made of graphene oxide and any other organic material composite using SILVACO. I would also like to know how I can add...

15 February 2021 5,795 3 View

Vth increase with programming SONOS Flash in Tcad?

Hello, I've been working on this issue for more than a month now.... I made a basic SONOS flash structure using TCAD Sentaurus sProcess. (tunnel oxide/nitride/blocking oxide : 4/6/6 [nm]) Then,...

11 February 2021 3,337 3 View

How to eradicate the deteriorated contact resistance in the electrical or electronic devices, like SCR or contactor' pin cable ?

Through years operation, some of the devices' pins connection gradually become worse and finally burn out due to the high temperature at the connection point. We can check out these risk points...

04 February 2021 7,401 5 View

Why sometimes current- voltage plot in chemiresistors/ FET does not pass through the origin?

I am trying to measure resistance from I-V curve from a chemiresistor/ FET sensor with a keithly sourcemeter. The substrate is soaked/ wet with protein and phosphate buffer only. But the I-V line...

24 January 2021 8,009 3 View

TCAD Simulation how to extract charge in electrode?

Hi, I am newbie in synopsys TCAD. I want to extract the charge information in electrode during transient simulation. I have seen this in TCAD Manual that I can get charge info from .plt file as...

21 January 2021 7,079 2 View

Is there a way to extract scalar and vector field data from Sentaures into a separate txt file to plot it in other software?

I have TDR file, which contains binary data that can be read using Svisual, a tool from Synopsys Sentaurus tool collection. I want to extract the vector and/or scaler fields such as Temperature...

05 January 2021 2,436 3 View

Navid Anjum Aadit

you can use center welled QW heterostructure to obtain unipolar tunneling.

Reza Meshkin

Dear Muhammad,

thanks for your reply, I would be glad that explain me in more details. Do you have a figure that show this structure?

Dr Shiromani Balmukund Rahi

https://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=6629285

http://nsdrl.dese.iisc.ac.in/wp-content/uploads/sites/3/2017/09/MEJ08.pdf

May be these articles can help to solve your problem

Very thanks Dr Shiromani Balmukund Rahi for useful links