How can the radial displacement of the back coil springs in the car can be measured during car travel?

More HASSAN ABDELWAHAB ABDELKARIM's questions See All

What is most convenient software for simulation vibrated bodies?

Project deals with analysing the vibration in light passenger vehicles

09 October 2018 1,000 3 View

What are proper test can be conducted on vetatable oil lubricant to insure it high cooling and lubrication charactrestics?

We are testing different vetatable oils in turning process.

09 October 2018 1,341 0 View

What is the relation between the matreila yield strength and stress relieving in heat treatment processes?

When annealing certain coated material on different substrate material the yield strength of one of materials plays role in relieving the internal stresses.

01 February 2015 5,432 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

In an eye with Tyndall, does each dot correspond to an individual cell?

When you observe the presence of Tyndall in an inflamed eye: Does each of the small floating dots correspond to an individual cell or to an aggregate of cells? Does a conventional slit lamp have...

27 February 2021 6,326 2 View

Why am I getting 'Infinity' and 'NaN' in my mixed-mode energy release values?

Hi everyone, I am currently running a mixed-mode simulation of a DCB using a user-defined cohesive zone model (UEL), however, the results I am getting don't make sense. I used the same UEL for...

24 February 2021 4,157 1 View

How can I obtain time series data by country on night-time light (brightness) ?

Hi everyone, Please, how can I obtain time series data by country on night-time light (brightness) ? I've tried, but so far all I can find are maps. I am looking for numerical data, especially in...

24 February 2021 8,625 4 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

What are difference between laser diodes, simple light emitting diodes and power light emitting diodes when operated in the visible spectrum ?

I want to illuminate a scene (small space) using LED to capture photographs or videos of some tiny objects inside the space. But am not sure if I should use a Laser LED, or simple LED or power...

22 February 2021 4,240 4 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

Claes Richard Fredö

Put a sensor in the skewed radial direction between a coil loop, e.g. a LVDT, wire position gauge, or even a long strain gauge should be able to do the job. The suggestion assumes the coil center to be free from protruding objects.

HASSAN ABDELWAHAB ABDELKARIM

Thank you dear Claes Richard for your answer

Best regards

Jumaa Salman Chiad

It is a very interested question

I agree with Claes answer

Thank you dear Jumaa