How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How can I find eddy size distribution in ANSYS Fluent?

Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...

01 February 2021 731 1 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

How to match results from based paper and Ansys Workbench in modeling piezoelectric?

Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...

13 January 2021 7,356 3 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

What is the difference between organic perovskite solar cell and inorganic perovskite solar cell?

Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks

01 January 2021 4,310 6 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View