I am unable to find the correct simulation result of DXCCII. I have designed DXCCII using CMOS and simulated by HSPICE using 0.18 μm TSMC lib.
Can anyone suggest what mistake i have made?
Waveform is attached.
You can try different combinations of analog building blocks, you can see this paper:
As i can see the Figure , it has the DC offset. My suggestion please go through the following paper.
The dual-X current conveyor (DXCCII): A new active device for tunable continuous-time filters .
Solve this paper analytically and mathematically. Then apply for simulation.
sure sir... Esteban Tlelo-Cuautle
Tajinder Singh Arora ys sir... i have read this paper but not able to find my mistake...again i will try to understand the concept...
i have the enzymatic antioxidant assay by following the method of Misra and Fridovich, 1972 for super oxide dimutase and Luck, 1974 for catalase assay can any help me how to the calculation for...
11 February 2021 2,241 3 View
I am synthesizing 7 amino acid long peptide sequence with CTC resin, 50oC coupling for 10 min. On cleavage (TFA/TIPS/Water 95:2.5:2.5) I got peptide with good yield. However, It has 68 Da more...
30 January 2021 8,483 3 View
I have gone though few papers related to this problem. Researchers used NS2.35/2.38. and MATLAB. Also. My particular question is regarding congestion control . Which will be more suitable to use ?
22 December 2020 8,197 10 View
My study is to use only fixation and saccade data. But after removing :unclassified' and 'eye not found' data. I come to know there is 2 back to back fixation duration or saccade what I need to...
28 September 2020 9,919 3 View
Need to know specific parameters which impact the learning culture variables.
23 September 2020 233 4 View
In health related studies, can the level of precision be taken as 0.07 or 0.08 while calculating sample size?
19 July 2020 3,230 3 View
In this project on agricultural waste management, we will discuss the problem of agricultural waste, how it can be managed, and its legal framework. Area of study: Distt Patiala and Ludhina,...
13 July 2020 8,112 4 View
i m doing academic research for automatic detection of duplicate bugs . so i required bug data
14 May 2020 6,846 1 View
I have a particular RF Switch with me that I need to test on CST. Is there any way to import the data of that particular RF Switch (such as equivalent circuit and/or S parameters) and test my...
22 September 2019 5,063 1 View
What are the emerging issues and contemporary dimensions in Corporate Governance field in India.
25 March 2019 449 5 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...
01 March 2021 2,327 1 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...
24 February 2021 3,476 4 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...
24 February 2021 5,974 4 View
Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...
23 February 2021 9,159 3 View