And suggest ideal technology and topology
This might be a good reference for you
http://upcommons.upc.edu/e-prints/bitstream/2117/10669/1/Medium.pdf
use matlab
Dear Harimi,
You need a rectifier and you may use a diode bridge or a tyristor controlled bridge in order to converter AC to DC. It can be 6, 12, 24... pulses, it depends of yours requirements. Here is an exemple of matlab of three phase controlled rectifier.
http://www.mathworks.com/matlabcentral/fileexchange/37594-three-phase-fully-contolled-bridge-rectifier
Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?
25 February 2021 4,075 1 View
Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks
23 February 2021 6,518 3 View
Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...
14 February 2021 3,606 2 View
The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...
08 February 2021 657 16 View
Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...
01 February 2021 731 1 View
Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...
22 January 2021 2,352 2 View
Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...
13 January 2021 7,356 3 View
Hello to all What is the gradient thermal annealing (GTA) process?
06 January 2021 7,740 2 View
Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks
01 January 2021 4,310 6 View
Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)
27 December 2020 9,350 4 View
When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.
16 June 2021 0 0 View
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...
02 March 2021 2,431 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...
01 March 2021 9,537 2 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View