Where did Mitoprot software go (download version)?

Hi all! I've been using local copy of Mitoprot software for prediction of gene localization. https://ihg.gsf.de/ihg/mitoprot.html I've updated my laptop and now need to download Mitoprot again,...

18 January 2021 4,368 3 View

Greiner Bio or Corning Costar plates for ELISA?

09 December 2020 237 2 View

Reverse power analysis to calculate optimal sample size after regressions and mixed effects models?

Hi All, I have conducted a pilot study with a small sample (50ppts), 2 groups - intervention (n=34) and control (n=16), pre-post-follow-up design. I've done linear multiple regressions (similar...

19 November 2020 8,578 4 View

SEM: correlations between latent constructs greater than 1. How to treat multicollinearity?

I am doing a CFA in SPSS Amos, and I face the following problem. 2 of the latent constructs are highly correlated (Amos provides the estimate of greater than 1). Could please someone advise how to...

17 April 2016 7,743 13 View

Two questions about SEM: how to introduce new indicators? How to develop hypotheses?

Dear Researchers, I am quite new to structural equation modeling, therefore, I would like to ask you a question. In my research, I use a questionnaire to collect data for testing the structural...

16 February 2016 4,522 3 View

Can anyone help with the acoustic streaming effect of turbulence?

I would like to implement acoustic streaming influence on turbulence in COMSOL. Can anyone help me to make the transition from acoustic module to fluid flow module? Has anyone already done it? I...

11 May 2014 9,792 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View