How can I plot real and imaginary susceptibility from KKR-CPA code?

More Peram sreenivasa Reddy's questions See All

Dear all, Iam currently working on Dc Microgrid model for electrical vehicle charging. Can any body give good IEEE research paper on this topic?

please give any suggestion?

04 February 2021 4,837 5 View

What does the change in D-peak position in Raman spectroscopy of carbon materials indicates?

We have carried out high-pressure Raman characterization on some of our samples. After fitting, I have observed a change in D-peak position with increasing pressure. What does this change...

20 January 2021 853 3 View

PSFB control signal?

Hi everyone iam facing a problem to give control signal for switches in design of PSFB converter in matlab simulink. Anybody's help will be appreciated.

14 December 2020 6,021 3 View

What is the correct method to calculate 50% end point in virus neutralization assay?

Neutralizing titer is defined as the reciprocal of highest serum dilution required for neutralization of 100 TCID50 of the virus in 50% of the wells. In general, serum is diluted in a twofold...

10 December 2020 3,547 3 View

What are the alternative to the pozzolanic materials to in concrete to enhance the durability of concrete?

As of now, Only industrial wastes were using as pozzolanic materials in concrete to enhance the durability of concrete. Can any once suggest me the alternatives of those materials?

11 October 2020 3,569 4 View

Can any one suggest me the dielectric constant of Gold and Co3O4 at room temperature ?

i have a question regarding dielectric constant of gold,cobalt oxide (co3O4) and n-tpe silicon . i find only one publication on this issue showing dielectric function cobalt oxide(CoO) 12.9 and...

02 October 2020 9,138 4 View

Eupergit beads for enzyme immobilization?

We are looking to immobilize some of our enzymes on Eupergit beads. I was wondering if you know any commercial supplier of Eupergit beads?

28 September 2020 5,664 3 View

Can somebody kindly suggest a good FEM software for the numerical solution of stochastic PDEs?

Please kindly suggest some good FEM softwares for the numerical solution of both time-dependent and time-independent stochastic PDEs.

28 September 2020 6,598 4 View

How to run Seismic analysis for the following model in OpenSees..?

I have developed a 3 bay 5 story 2D frame in Opensees but I have problems with element load and application of seismic load in Opensees using an acceleration file. I always got an error namely...

27 September 2020 5,885 4 View

How can we evaluate the conductance of a constant power load (CPL)?

Any CPL is modeled with a current source in parallel with negative resistance. How do we evaluate the negative resistance, if we know the constant power consumed by the load?

19 September 2020 6,188 3 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How do I choose contrasts in SPM8?

I am learning how to use SPM for PET and PET-MR analysis, but I haven't found any great resources that explain how contrasts work. I have a series of PET images where our hypothesis argues that...

24 February 2021 1,534 2 View

How to make a time series imputation benchmark ?

Hello ! In a work, I have to benchmark different algorithms to fill in missing values in time series. I insist on the fact that this is imputation and not forecasting. In my case, I have access...

24 February 2021 7,470 7 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View