How can I model a segmental tunnel lining joint using Flac2d?

More Majid Ghasemi's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

How does stream gradient steepness change moving downstream and gradient of a stream change along its longitudinal profile?

12 July 2024 4,113 0 View

Which size of undersized iron pellet is suitable for sponge iron tunnel kiln production?

Someone advise me to use 1 to 2mm undersized pellet but it is not available. Do anyone have any experience in the field of tunnel kiln ?

28 June 2024 6,355 0 View

How to analyse category membership changes over time?

I have a longitudinal dataset where I am looking to examine whether individuals change their category membership of a variable (with four categories) over four time points (baseline, 1y, 2y, 3y)....

16 June 2024 9,770 10 View

Tunnel Analysis in FLAC3D - How to create a liner in a tunnel?

Anyone knows the code to create a concrete liner/shell in a tunnel with a thickness = 0.25 m using FLAC3D 5.00?

05 June 2024 4,998 0 View

How can I use proc nlmixed for two-level joint model for data that is not longitudinal?

11 May 2024 4,239 0 View

How can I find longitudinal tumor growth data?

We developed a mathematical model from mathematical point of view and we need tumor growth data that reflect number of tumor cells respect to time for our validation. We are not expert in this...

02 May 2024 491 3 View

On Structural Equation Modeling Results?

I'm currently doing my thesis which uses structural equation modeling for longitudinal data. Is it normal for a model to have 0 RMSEA, Test Statistic, Degrees of Freedom, and p-value? What does...

12 April 2024 2,358 3 View

What Australian longitudinal studies of youth transition to employment, including youth in care have been undertaken?

Longitudinal studies of youth transitions in Australia

28 March 2024 7,368 0 View

Is it possible to fit a GEE model with an outcome variable that is not normally distributed and only has a value score of 0-8?

I have a longitudinal data with 3, 6 and 12 months. I am thinking of using GEE in order to handle these longitudinal data sets. However, my problem is I have an outcome variable that is not...

11 March 2024 1,349 2 View

What should be the minimum time interval required for longitudinal studies to be conducted?

can this time interval be for 6 months ? if the data is collected twice in a period of year. is this considered longitudinal studies ? what is the degree of freedom if some of the participants...

07 March 2024 1,111 4 View

Sadiq Shamsher

yes you can model the joints in FLAC 2D. In 2D, you can model joints by assigning axial and tangential stiffness along x and y axis and rotational stiffness about z axis, to assign these stiffness you can use springs. see this thesis

http://www.theses.fr/2014ISAL0042.pdf

Majid Ghasemi

Tnx Sadiq, But I think this link has a problem. Can you send it again or write its title?

please type this link in google search engine, first link will be of this thesis