How can I mix ferrite nano powder is synthesized by auto combustion method with epoxy resin to build a paint?

More Miraliasghar Sedaghati's questions See All

Does aggressive driving necessarily lead to dangerous driving? Does a driver's performance reflect his behavior?

I want to research on aggressive and dangerous driving behavior. first I want to know does an aggressive driver necessarily dangerous driving? I mean if one person shows aggressive behavior, I can...

26 December 2019 7,780 3 View

What is the effect of season and irrigation system on mycorrhizal colonization in almon? our data shows higher colonozation in winter?

i want to know, why colonization percentage could be higher in winter than summer?

16 April 2017 8,846 4 View

Nano Orange protein quant on the Quantus fluorometer?

Is anyone here using the Thermo Fisher Nano Orange kit for protein quantification, and detecting the fluorescent signal on the Promega Quantus? We are struggling to make sense of the standard...

05 August 2024 8,946 3 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ?

Good evening, I would like to evaluate the heavy metal content in bird feathers. Can I keep my samples in powder form ? and can I use other tubes than Teflon for digestion?

04 July 2024 158 4 View

Sadeq H. Lafta

Are the mentioned ratios weights or volumes ratios? It is difficult to spread it as homogeneous paint with high ferrite content. I think, You can use some diluting solution with epoxy mixed thoroughly by some fast mixer machine then you can add resin with some moderate mixing.

Ahmed Hmeed