How can I make a super hydrophobic coating with silicone oil?

04 April 2023 0 2K Report

Hi all,

I want to first disperse silicone oil with viscosity 1000(mPa.s) in water. Then I make a super hydrophobic coating. Is it possible? Can anyone help me?

Badges
Science topic

More Rana Monavari's questions See All

How to do pca analysis of c-alpha atom of the protein?

i m interested in pca analysis of c-alpha atoms in gromacs for that i used the following gmx_mpi covar -s mdca.tpr -f mdca.xtc -o eigenvalca.xvg -v eigenvecca.trr -av average.pdb -n index.ndx but...

30 July 2024 1,607 1 View

Getting this error : gmx_mpi': corrupted size vs. prev_size: 0x0000000001d1b320 ***?

i am using the trjconv command in gromacs gmx_mpi -debug trjconv -s md.gro -f md.xtc -o utr.xtc -fit rot+trans and after few steps i got the error gmx_mpi': corrupted size vs. prev_size:...

17 July 2024 6,216 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Any suggestions to enhance the wettability and adhesion of fluorosilanes?

I am facing a difficulty to prepare the thin film which contains fluorine contained silica monomer, as we know F is highly reactive with low surface energy and it could be the reason of low...

09 July 2024 6,017 3 View

Why is the mouse intestinal organoid not forming ?

I am isolating the crypt from mouse small intestine the following several modification of EDTA concentration, 3mM (30 min), 5mM (30 min), 20mM (25 min) at 4 degree. For all the EDTA...

09 May 2024 9,005 2 View

What correction is used when 95%aCI is overlap ?

How we make 95% CI (lower and upper) far, when overlap in analysis, whether we can use effect size to make difference in lower and upper interval

03 May 2024 1,846 2 View

Is Pluriselect a good company to buy kits for cell separation?

I am recently buying kits from Pluriselect to take out (deplete) NK cells and CD4 cells from blood. The main reason me using this is cheap and do not require accessory equipment. But in Pubmed...

02 May 2024 5,861 1 View

WARNING: FENE bond too long: 1 7 8 32968539.141547877 (src/MOLECULE/bond_fene.cpp:83) ERROR on proc 0: Bad FENE bond (src/MOLECULE/bond_fene.cpp:85)?

# Polymer chain simulation with FENE and LJ potential in NVT ensemble # Initialization units lj # Use LJ units atom_style bond # Atoms and bonds boundary p p...

16 April 2024 5,828 0 View

Bond broken in fene potential?

i simulating a single chain polymer with 10 particle with fene and lj but if i increase the no of particle my bonds are being broken . im using parameters as below 20 50000.0 0.1 1000.0 1.0...

15 April 2024 2,748 0 View

How to calculate the center of mass coordinate of the protein in gromacs?

i want to find center of mass coordinate of the protein,for that i using the following command gmx_mpi traj -f md_noPBC.xtc -s md.tpr -com -ox com.xvg -pbc but i m not getting satisfactory...

04 March 2024 814 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

I need to dissolve stigmasterol for an animal experiment, it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent?

Hello everyone, I need to dissolve stigmasterol for an animal experiment, but it hasn't dissolved in either DMSO or vegetable oil. Can anyone recommend the best solvent for stigmasterol?

01 August 2024 7,504 2 View

How to treat monolayer culture cell line with essential oil?

Hi all, may I ask you for advice about treating monolayer culture cell line with essential oil. Due to the hydrophobic character of the oil, I am concerning how can it equally affect to all the...

31 July 2024 5,301 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View