How much amount of DNA (ligation mix) should I use for transformation?

Hi Fellow Scientists! I am trying to clone my 300 bp insert into a 6 kb vector. I run a few different ligation reactions using (1:3 vector: insert molar ratios) 10, 20,30, and 40 ng/ul vector...

15 February 2021 9,563 6 View

How to choose proper spindle for measurement of thixotropic behavior of ceramic slurry?

Hello, we are studying on thixotropic behavior of ceramic slurry . We will perform the thixotropic behavior analysis of ceramic slurry with the density of 1,7 g/ml by using BROOKFIELD DV2T. How to...

08 January 2021 1,776 5 View

What is the proper concentration for measuring zeta potential of ceramic slurry?

Hello, we are studying on electrophoretic ceramic coating. We performed zeta potential analyzes using zetasizer to decide whether the ceramic slurry prepared is suitable for the EPD method. We...

29 November 2020 9,395 7 View

How post-hoc test should I perform for two way repeated measures ANOVA for 3 groups?

Hello everyone, I have 3 groups and 4 measurements so, I performed two-way repeated measures ANOVA. How can I detect the difference (which groups and which measurements) when there is significant...

27 October 2020 4,503 3 View

How do We Maintain Appropriate Cell microenvironment with 3D Cell Culture Method?

3D Cell Culture is newly optimized and promising discovery in cell organization research and other researches that needs evindences in cell culture (in vitro) level. Are 3D Cell Cultures mimic...

23 September 2020 7,109 4 View

How do We Clarify the Effects of Drugs on DNA Replication?

DNA Replication and its components are common targets in discovering new drugs as antimicrobial therapeutic agents especially while dealing with antibiotic-resistant species and other diseases...

21 September 2020 6,172 4 View

Can you give information about how to calculate the molarity of MEA?

Hi, I am trying to produce CZTS films by sol-gel spin technique. Can you give information about how to calculate the molarity of MEA? Did you calculate the MEA molarity separately for each metal...

11 July 2020 3,415 1 View

Do weak contribution equations within a module use the module's boundary condition in COMSOL?

I am trying to solve a partial wave equation for scattered quasi-TE waves. I found the COMSOL built-in Helmholtz equation module very close to my problem. The bottleneck was that, I couldn't...

03 June 2020 8,937 1 View

How Can I find a reverse primer with good rating, if I need to amplify entire gene?

I need to amplify the KCNA1 gene. I could not design the reverse primer with GC content ~50%, G/C content between 40-60%, rating 100, and no secondary structure. Any help much appreciated!

25 May 2020 7,276 9 View

Is it possible to have more elements than nodes in mesh analysis of ansys?

During Centrifugal Pump Simulation by using ANSYS, I obtained more elements than nodes. Is this possible or the number of nodes should always be greater than number of elements?

04 May 2020 4,700 11 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

What degree of missing data in a particular case/participant results in Expectation-Maximisation no longer working?

I'm dealing with a mediation model and am using the PROCESS module in SPSS. Due to SPSS and PROCESS being limited in the imputation methods - being unable to handle multiple imputation - the other...

02 March 2021 4,362 1 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

Mixed ANOVA - help?

I'm currently working on a piece which asks to conduct an ANOVA - looking at the effect of sporting group (2 levels), and exercise trials (two trials with six levels). I've computed this all...

27 February 2021 9,626 4 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View