Whether the engineering stress-strain curve or true stress-strain curve could i use to get young's modulus and yield stress of material?

like the title. I have done the compression test and get the engineering stress-strain curve. If i want to get the young's modulus and yield strength, do I have to make true stress-strain curve?...

07 August 2016 7,562 10 View

How to calculate the heating rate or heating time during annealing Nickel 625?

The material for annealing is nickel 625. The process of annealing treatment is firstly heat the furnace to aimed temperature, then put the sample in the furnace and start to record the time when...

01 January 1970 6,895 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

What is the difference between genotype and haplotype data in the ped format?

Hi everybody In the ped format for genotype, alleles of any SNP are represented by two columns (one for each allele, separated by a space). Is a column sufficient for the haplotype to...

27 February 2021 1,965 1 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View