How can I get rock density data in the Great Basin Area of North America?

11 November 2017 0 3K Report

I want to make a modelling subsurface in the Great Basin Area in the California, Nevada, and Utah. But I don't have subsurface data of rock density in that area. how can I get rock density data in the Great Basin Area of North America?

Badges
Science topic

Similar topics
Engineering
Modeling

More Nia Tanjung's questions See All

How to get free-air data from Topex?

I am trying to make gravity modelling from Topex data, but I am still confused about how the Topex satellite using Altimetry can calculate the value of free-air anomalies. how to get free-air data...

11 December 2017 3,521 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Do you think can be any Uranium bearing rocks in Eastern part of Iran and western part of Afghanistan?

I want to know more about Uranium ore deposits in world.

11 August 2024 6,720 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Why do exism movements become permanent dictatorship threats within liberal democracy thinking under majority rule-independent rule of law system?

Exism movements after gaining power within liberal democracies under majority rule and independent rule of law system become permanent dictatorship threats, but why this is the case is not clear...

04 August 2024 8,125 3 View