How does SEA software normally number subsystems?

Dear colleagues, What is the common subsystem numbering system in SEA modelling software (i.e. VA One, AutoSEA2)? Cheers, Feng

27 February 2021 7,073 3 View

(Scale request) Anyone has the Malay version of Eating Attitude Test-26/40 (EAT-26/40)?

Dear Researchers, My research team is conducting a eating disorder related research in Malaysia and we would like to use the Malay translated version of EAT26/40. I have tried to email the...

24 January 2021 8,925 2 View

How to search the specific primer for genus Sphingobium ?

Dear all, I want to find a specific primer for genus Sphingobium, could you give me some idea on it? Thank you so much~

13 December 2020 4,455 4 View

Why case-controlled study is more bias prone than cohort study?

I noticed from several articles saying that case-controlled study is more bias prone than cohort study (in the context of cancer early detection using molecular marker). I spent sometime to try to...

17 November 2020 1,878 4 View

How to get the right result of iwr1443?

05 October 2020 10,015 3 View

Can we compare Bray Curtis dissimilarity indices calculated i) from proportions and ii) raw values ?

Hi everyone! I have a technical question here related to ecological distance indices. I have calculated a Bray-Curtis dissimilarity matrix for several sites using the raw abundance value of...

09 September 2020 2,752 1 View

Why the gold turns from grey to red after sputtering on PTFE?

Hi all, Recently, I sputtered some gold on the surface of PTFE with a thickness of 1 nm and 3 nm (Please see the attached). The color was grey when it was done. However, after about one day, the...

19 August 2020 1,267 3 View

If cell pellet has been stored in -80 for two years. Can RNA be extracted for mi-RNA Seq? Would it be of good quality?

Hello everyone! If cell pellet has been stored in -80 for two years. Can RNA be extracted for mi-RNA Seq? Would it be of good quality? And what's your recommended methods of RNA extraction from...

30 June 2020 3,947 1 View

How to inhibit or supress cracking in Ni-W electraodeposition?

I'm try to synthesize Ni-W alloy using DC electrodeposition. However, plenty of cracks were found in the Ni-W deposits with a relative high W content (approximately 20 wt.%). Is there any...

11 June 2020 442 5 View

I am reading journal paper about mangroves. And I would like to get some recommend journal related to dissolved oxygen influence on mangrove growth?

I am wondering, why my study result show that Kandelia candel and Avicennia alba species are most sensitive towards soil dissolved oxygen (DO) besides R. apiculata among the mangrove species in...

27 May 2020 1,366 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View

How can we quantify martensite in Ferrous and Titanium alloys?

How can we quantify metastable phases like martensite in Ferrous and Titanium alloys, in relation to their stable counterpart For example in EBSD, XRD, Optical? Eg, Martensite and Ferrite maps.

09 February 2021 7,572 3 View

About forging of Mo Alloys ?

Hello dear Academicians, I am working on the forging of Mo alloys, but I wanted to consult you on an issue I could not solve. Mo is easily oxidized during forging and MoO3 is formed. Is it...

09 February 2021 1,989 3 View