How can I get data for yield stress and plastic strain for ABS in ABAQUS? and is it possible to do motion and extrusion simulation simultaneously ?

08 July 2019 0 8K Report

Hello, I'm doing extrusion simulation and for that I need yield stress and plastic strain. if possible then related to its temperature. 2) is it possible to do motion and extrusion simulation simultaneously ?

Badges
Science topic

More Jay Prajapati's questions See All

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,851 1 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,309 7 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

How we can use lattice-based cryptography for construction of S boxes?

Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.

24 July 2024 6,291 4 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,348 2 View

Can it is possible to find the cleaved sequence when a protein cleaved by a heamaglutanin protease (HA/P) by any bioinformatics tools?

Bioinformatics tools like peptide cutter

15 July 2024 6,453 1 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

FACS markers to characterize rat bone marrow-derived macrophages?

Dear all, I am looking for FACS markers to characterize my rat bone marrow-derived macrophages (M0). They were differentiated from monocytes with M-CSF. I am considering to use CD11b/c and...

15 July 2024 4,615 1 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View