How can I get a MATLAB code of numerical methods for solving systems of singularly perturbed boundary value problems?

More Aditya Sharma's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

If my gene of interest has high GC content can it be problematic in sequencing? What kind of error is expected with GC rich gene sequences??

Gene sequencing related trouble shooting

25 July 2024 4,149 2 View

How to dispose off lipids waste?

I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...

25 July 2024 637 5 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

How effective has the United Nations been in addressing the conflict and its consequences?

After World War, we have seen the formation of the United Nations. The sovereign body for peacekeeping but with regards to the Russia-Ukraine war it is visible that the UN seems to be ineffective...

18 July 2024 4,674 4 View

What are the main obstacles to achieving a ceasefire or peace agreement between Russia and Ukraine?

It has been a quite long time since the Russia and Ukraine war has been going on and if we see the context of Geopolitics and International Relations we don't see a mediation between the two...

18 July 2024 6,737 4 View

How to decide whether the refinement is correct or not, based on Rwp and Rexp factors by Fullprof?

One of the papers I read by Toby, where (title of the paper was "R factors in Rietveld analysis: How good is good enough?"), he tells us that to get good chi square value, you must have low Rwp,...

17 July 2024 9,668 4 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What are possible strategies can be used to analyze data under sequential explanatory mixed method approach?

Better ways to analyze the qualitative and quantitative data in a sequential explanatory mixed method approaches

04 August 2024 2,703 6 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

What is the acceptable p-value cutoff for GO enrichment analysis ?

I have an RNA-seq data that I have analysed using Limma-voom and have extracted the gene IDs, log2FC and the p-values. At p value < 0.05, I have over 10,000 DEGs, however, when I run the GO...

31 July 2024 225 2 View

How to do Mann-Whitney U test with Bonferroni corrected p-values?

Dear All, My lab primarily works on insect wing patterns. In one of the projects, my student and I have defined 19 abnormality characters on the forewing and 6 abnormality characters on the...

31 July 2024 6,464 5 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

Request for Advice: Starch Metabolism Research Project?

I am currently considering a research project focusing on a comparative analysis of starch metabolism in orchids and roses. I am particularly interested in identifying the types and quantities of...

30 July 2024 4,267 2 View