I have Synthesised Lithium rich layered oxide (Li1.15Ni0.23Co0.08MnO2)and took powder XRD Patteren,now i would like to do riteveld refinement ?

I have synthesised Lithium rich layered oxide(LLO) (Li1.15Co0.08Ni0.23Mn0.54)O2,now i want to do riteveld refinement for LLO by using full prof software.How do I can start to do it to find out...

05 June 2018 9,180 0 View

Lithium ion battery band diagram,why the cathode potential above the homo and anode potential below the lumo ?

As we look in to the banddigram of Lib with the half cell and full cell configuration ,the electrodes cathode chemical potential above the homo and anode chemical potential below the lumo?why and...

07 August 2017 4,317 5 View

How do we calculate the therotical surface area calculation for 200 nm ,1micron meter and 10 micron meter?

how the particle shape can changes influence the surface area calculation from nano to bulk ? in my sample the particle are plate shape. what we have to consider if the particle are in homogenous...

06 July 2017 6,570 2 View

Why the diffusion coefficient of cathode materials finding from cyclic voltametric and electrochemical impedance spectroscopy the value changes?

06 July 2017 8,152 2 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

How to predict the reaction pathway for electro organic synthesis?

Can anyone recommend some any software/models available that can predict substance reactivities and the reaction yield under a specific set of reaction conditions process and proposing pathways to...

17 February 2021 2,383 3 View

Is there a paper that shows the effect of the thermal conductivity of solid electrolytes on lithium secondary batteries?

I want to know the effect of thermal conductivity characteristics of solid electrolytes on the all-solid battery, but I don't know which paper to refer to. Is there a paper on thermal behavior?

15 February 2021 8,806 2 View

Solution of 2D convection diffusion heat equation using MATLAB ?

This is a polymer heating problem. Polymer enters at around 180C (x=0) in the barrel. Also barrel initial temperature is 180 (t=0). Some heat Is added along whole length of barrel q. We have to...

15 February 2021 3,887 1 View

Defining effective diffusivity in porous zone and non-porous zone?

Hi all, I am working on methanol steam reforming using packed bed for hydrogen generation. I am using FLUENT software for CFD simulation. In reference paper, authors mentioned that effective mass...

10 February 2021 6,104 1 View

How to match the XRD of a compound for which there is no JCPDS file ? Is there any other characterization to claim the synthesis of desired compound?

I have synthesized LiMgF3 using the starting precursors LiF and MgF2 via solid state diffusion method. Now I am looking for some characterization to claim the desired product, as there is no...

09 February 2021 921 3 View