How can I estimate the effective diffusivity coefficient in the mathematical modeling of the leaching operation?

More Danger Tabio García's questions See All

Can someone provide me reports of effective diffusivity in the extraction of oil from of Moringa oleifera seeds?

I need reports from the literature that have calculated coefficients of effective diffusivity in the extraction process of Moringa oleifera oil using the Soxhlet extractor

11 December 2017 8,663 0 View

How to implement Nernst's law in a leaching operationt?

I need to corroborate if it is necessary to establish several stages of extraction

10 November 2017 5,336 7 View

How to solve a partial differential equation by the finite difference method in Matlab?

I just want a tutorial or a code for resolve the EDP

09 October 2017 5,974 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Is there a problem with my RNA pellet?

Hello, I am currently having problems with RNA extraction. I am using mouse liver (C57BL6J), and I have extracted RNA from mouse liver before. Before this experiment, my final RNA pellets were...

11 August 2024 7,082 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View