How can i design a simulink model from multiple differential equations ?

07 July 2015 0 6K Report

i m working on railway suspension model and that model has multiple equations, i have to design a simulink model from those equations.

Badges
Science topic

More Noman Ghulamullah's questions See All

How to couple mass transfer and momentum equations in SOFC modeling?

i am working on SOFC modeling and looking for equations and their implementations , but i am confused how would i couple all the equations ?

05 June 2019 9,414 3 View

Fourier orthogonal basis expansion for FESN time series classification ?

i am working on a FESN time series classification but i am unable to understand the expansion of fourier orthogonal basis which is used for the output weight matrix learning. can you please guide...

10 November 2018 6,529 0 View

How to normalize a random acceleration signal between 0 and 1 range?

Hi , i am working on fault detection of a plant and i need a normalised value of the residuals for fault detection using fuzzy. how and what formula or simulnk block can help me sort out this...

10 November 2016 9,698 3 View

How and what form of state space modeling is necessary for a model based fault detection using fuzzy?

i am working on fault detection of a suspension system using fuzzy. problem is i have to convert my model (differential equations) into space space form. but in which form i can convert it ? need...

06 July 2016 319 4 View

How to design a fuzzy controller in matlab ?

i need to design a fuzzy controller which can compare actual running model with multiple faulty models and detect and identify the faulty model with the running model if some fault is introduced...

03 April 2016 4,273 2 View

How can i design kalman filter estimator for railway suspension system?

i am working on my postgrad thesis, and i am going no where in it. i am working on kalman filter which is very difficult for me to design. i need to know what i should do if i have few almost 7...

02 March 2016 3,969 3 View

Can anyone help with the modeling of a railway suspension system?

i intend to design a simulink model

04 May 2015 1,375 5 View

How to normalise a output value which is random to a range of [-1 1]?

i am working on a simulink model and need to normalise the output values to -1 to 1 so that i can imply fuzzy controller easily. i am working in simulink environment. Regards:

01 January 1970 4,823 5 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Dear Professor/Researcher, I want to use LoRa to send a signal with a frequency of 10 kHz. Is this feasible or not?

I use LoRa with Matlab/Simulink

23 June 2024 3,847 3 View

Aspen Adsorption linking to MATLab ??

Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...

20 June 2024 8,338 2 View

Does anyone know where this module is in Simulink?

I try to build a three-phase wireless power transmission model and saw this module in an article.

27 May 2024 3,471 2 View

Can you help me for do this matlab simulink project?

I'm new. I know just little use of matlab. Help me for do this matlab simulink project.

25 May 2024 4,247 1 View

Simulink model for ANC earmuffs?

Adaptive Filters are core of the ANC system. They continuously adjusts its filter coefficients to minimize the error signal, effectively generating the anti-noise signal. Common choices include...

21 April 2024 4,468 1 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Any suggestions to implement TECS on MatLab/Simulink?

Hi, I am trying to implement the TECS core algorithm to my closed-loop 3DoF model of the aircraft in MatLab/Simulink. The tuning of the innermost loops was accomplished succesfully, but now I am...

17 March 2024 8,446 1 View

Who has work on droop control for grid forming ??

could we make grid forming as stand alone inverter and control it by add active power ref and frequancy and voltage for rl load ? who has work on it in matlab simulink ? for me i did it for rl...

11 March 2024 6,303 0 View

Find a controller for a feedback-loop?

My team and I are working on an automation project to stabilize the altitude of an airplane. However, we've encountered an issue that seems unsolvable for us, at least for the moment, in the final...

03 March 2024 7,659 0 View