Can anyone help with the modeling of a railway suspension system?

More Noman Ghulamullah's questions See All

How to couple mass transfer and momentum equations in SOFC modeling?

i am working on SOFC modeling and looking for equations and their implementations , but i am confused how would i couple all the equations ?

05 June 2019 9,414 3 View

Fourier orthogonal basis expansion for FESN time series classification ?

i am working on a FESN time series classification but i am unable to understand the expansion of fourier orthogonal basis which is used for the output weight matrix learning. can you please guide...

10 November 2018 6,529 0 View

How to normalize a random acceleration signal between 0 and 1 range?

Hi , i am working on fault detection of a plant and i need a normalised value of the residuals for fault detection using fuzzy. how and what formula or simulnk block can help me sort out this...

10 November 2016 9,698 3 View

How and what form of state space modeling is necessary for a model based fault detection using fuzzy?

i am working on fault detection of a suspension system using fuzzy. problem is i have to convert my model (differential equations) into space space form. but in which form i can convert it ? need...

06 July 2016 319 4 View

How to design a fuzzy controller in matlab ?

i need to design a fuzzy controller which can compare actual running model with multiple faulty models and detect and identify the faulty model with the running model if some fault is introduced...

03 April 2016 4,273 2 View

How can i design kalman filter estimator for railway suspension system?

i am working on my postgrad thesis, and i am going no where in it. i am working on kalman filter which is very difficult for me to design. i need to know what i should do if i have few almost 7...

02 March 2016 3,969 3 View

How can i design a simulink model from multiple differential equations ?

i m working on railway suspension model and that model has multiple equations, i have to design a simulink model from those equations.

06 July 2015 6,300 0 View

How to normalise a output value which is random to a range of [-1 1]?

i am working on a simulink model and need to normalise the output values to -1 to 1 so that i can imply fuzzy controller easily. i am working in simulink environment. Regards:

01 January 1970 4,823 5 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View

How to combat antibiotic resistance?

The increasing resistance of bacteria to antibiotics has made many infections difficult to treat, posing not only a threat to public health but also a major challenge to healthcare systems worldwide.

18 July 2024 6,688 3 View

How to prepare bacterial conditioned media to study the effect of bacterial secretome?

I would like to investigate the effect of bacterial secretome on cancer cells. How do you prepare conditioned media from bacteria?? conditions- time points - media I am looking for the best way...

17 July 2024 3,785 9 View

How can the resilience of agricultural systems be improved by both gradual climate change and increased climatic variability and extremes?

17 July 2024 3,681 3 View

How to model a non-minimum phase system?

In deriving a model of an LTI dynamic system, the model of the system does have no RHP zeros, however, when inspecting the step response, it reveals a non-minimum phase system represented by a...

14 July 2024 6,355 2 View

Deepak Unune

If you have the dynamic equations which governs the behaviour of railway suspension then using the blocks in simulink you can build the suspension model in simulink.

Vanessa Meloni Massara

Dear Noman,

I believe this book will help:

Optimal Design of the Suspension System of Railway Vehicles

Regards,

Vanessa

Noman Ghulamullah

Thank u Vanessa, let me go throught this book.

deepak yes i have differential equations but very complicated. help requiried in understanding them or try to design my own.

Xinwen Yang

please look at Wanming Zhai's vehicle-track coupled dynamics in China