How can I create a genetic design for F2 level?

05 July 2022 1 8K Report

I need to create a genetic simulation and test my method on it for my dissertation research. As I search, I saw it's possible with "MCMC" and I'm using R.

Did anyone create a population like that and can help me to solve this?

Badges
Science topic

More Erva Eser's questions See All

How can I make Isight interact Solidworks with Abaqus?

Hello Everyone, I need to optimize a simple beam natural frequency in Abaqus with Isight. I know in abaqus there is parametric tool but for more complex and further study I want to use Catia or...

25 October 2020 7,007 3 View

Masonry wall modeling issue (ABAQUS) - Is this related with material or constraint ?

Dear Abaqus users, I perform a static analysis with a Standard module on a masonry wall macro model. Four surfaces interact with a reference point in the middle of the model as in the photo...

14 July 2020 4,560 2 View

Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

Has anyone had luck using cell lines other than HEK 293 (such as COS1) to package lentivirus?

I am looking to package lentivirus in endothelial cells but I am opposed to using 293 cells due to personal ethics regarding the source. I have done some reading and saw that COS1, COS7, & CHO...

25 February 2021 3,030 1 View

What program can I use to caclulate dipole moment efficiently and without the need of excessive computation?

Hi, I am a third year chemistry undergrad doing my group project in which I need to predict the HPLC retention time of 20 aromatic molecules. to do this we require the chemical properties of these...

24 February 2021 1,384 3 View

Questio regarding micro/nano particles fabrication ?

I will start to fabricate micro/nanoparticles for growth factor release and I check out a procedure quite nice, however, it is lacking some details and since I don't have much knowledge doing this...

20 February 2021 199 2 View

Fractional derivative users, are you on the same page with me on the validity of the fractional order parameter, say alpha?

Taking a fractional ODE problem as an example. It has come to my attention that if the fractional order parameter is in the interval (0,1], many only presents results for alpha=0.9, 0.99. I saw...

08 February 2021 9,671 3 View

How do i remove dimer primer when amplifiying DNA because i see on the electrogram of DNA ?

when i saw my DNA target on the electrogram there was a dimer primer below on DNA target. how do i remove it ? what should i do ? thanks

03 February 2021 5,290 3 View

How to improve the yield for the reaction below?

I am trying to increase the yield for the reaction below. I did the column and I saw that the major side-product is the symmetric dimer formed by 4-bromobenzyl bromide. I imagine that NaH is...

20 January 2021 7,874 4 View

What could be source of contamination for seeing positive amplification in negative control?

Yesterday, I ran a gradient endpoint PCR with some primers and saw positive amplification for positive and negative for negative amplification. Running the same assay today, show positive...

13 January 2021 5,201 1 View

After CRISPR and single-colony picking, cells reverted to WT?

Hi guys: I have been doing CRISPR knock-in and knock-out and one seemingly impossible scenario keeps happening. In the CRISPR knock-in attempt I tried to add a tag on a gene of interest, so I...

07 January 2021 190 3 View

Selection of months in SPEI time series (6,9,12,24) ?

I did SPI and SPEI work through R studio. As you know, r program for each month; We draw results for 1, 3, 6, 9, 12 and 24 months. However, when interpreting the results, we interpret the 3-month...

01 January 2021 8,223 5 View