How can I increase the run speed of the ANSYS CFX v15 software?

I use core i7 processor. Adding the number of processors more than 2 number does not affect the speed of the run. How can I increase the run speed of the ANSYS CFX software more?

05 June 2017 1,562 3 View

In PSO algorithm which method in order to ensure that the solutions are the ones which provide more interest?

PSO does not guarantee the unique solution, so which method in order to ensure that the solutions are the ones which provide more interest?

01 February 2017 9,789 12 View

How can I merge 2 Semicircular faces that is meshed in Gambit?

I want to mesh near wall of circle thinner and center thicker. I don't want to use boundary layer mesh in gambit. Please see the figure.

11 December 2015 7,785 4 View

For modeling fluid flow in tube of a chimney with flat plate and Re=800, can the flow be laminar or turbulent?

diameter of flat is 2/3 of tube diameter.

10 November 2015 9,653 7 View

How can I write a UDF for special symmetry boundary condition in fluent?

I want to change normal vector of symmetry boundary condition.

10 November 2015 117 9 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Ideas for Phd's Thesis on pricing (Marketing)?

Hi everyone, I'm studying Marketing and I would like to write my PhD thesis on the topic of pricing. Any specific ideas?

02 March 2021 9,706 5 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to write a scientific report?

We are analysing scientific reports at University in great detail, so I wanted to find a scientific report about how to write a scientific report. Including detail such as what information to put...

02 March 2021 7,602 4 View

Could any one guide me, to write research proposal for grant? ?

We have one plant, the local people using this for controlling blood sugar, the toxicity and antidiabetic activity of the plant is not reported yet, please guide from whag should be the process ?...

02 March 2021 2,300 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

No title

01 March 2021 3,905 5 View

How to Balance Bench work with Reading and Writing?

I am a second-year grad student. I am finding it difficult finding time to read literature and write (things like qualifying exam, thesis, grants). I find myself so busy with bench work that I...

01 March 2021 3,325 4 View