How can I configure a network based on VoIP using OPNET modeler 14.5?

Ritesh chandramohan Sadiwala @Ritesh-Sadiwala

07 May 2015 1 610 Report

how can i configure a network based on voip using opnet modeler 14.5 ??

Sassi Maaloul

hi, can you help me to get this version (v17.1) if it's possible.

thanks a lot

Badges
Science topic

More Ritesh chandramohan Sadiwala's questions See All

Does religion have huge impact on cultural entity?

It is seen that a nation is born with a religious essence, but some nations do get birth depending on the strength of cultural aspects. But religion influences the presence of cultural identity a lot.

18 March 2024 8,374 4 View

Why I am getting big difference in heat flow (mW) in slow heating and fast cooling cycle? Can I move my cooling cycle near to heating cycle?

Can I move cooling cycles of 20 and 30 oC/min close to 10 oC/min?

08 March 2024 947 0 View

Can someone guide me about the readout circuit for resistive gas sensor?

Please guide me about the readout circuit for resistive gas sensor

14 January 2024 153 4 View

What are the parameters which affects the liveability of a rural settlement?

Wish to know the relevant variables or parameters that are important to be considered to assess liveability in any rural settlement/ non-urban settlement.

05 October 2023 6,085 1 View

I only have noisy radar signals. How can I use an adaptive filter to denoise it as I do not have any reference signal?

I read somewhere that a delayed version of the noisy signal can be used as the reference signal but then how can we get a clean signal from giving a noisy signal as reference?

25 May 2023 5,759 0 View

Do minorities lose cultural identity among majority?

In the above mentioned question, is it seen that individuals who live in a place as a minority group or community are being influenced by the trait of the majority? Do minorities lose cultural...

20 April 2023 567 12 View

How to teach non native English speaking rural students?

Is it indeed tough enough to teach non native English speaking students, English? In rural area, students show interest in learning English but is it compatible with the method of learning and...

12 March 2023 8,780 21 View

Is an article found?

It is seen that when an article is manually uploaded in google scholar, it is not found while searching, what is the reason behind it?

05 March 2023 6,250 1 View

What if there are dissimilarities between template and suggestions after review?

I have found that I arranged my papers and sent the paper to a journal regarding journal template but later they advised me to do some corrections. There it is seen that template and their advice...

23 February 2023 6,779 0 View

One of my papers is accepted and available online, can I upload it in researchgate, google scholar?

Few days earlier I saw an article but the publication date mentioned was later than the current date. Can I do the same?

22 February 2023 2,011 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View