How can i calculate average temperature of an element in APDL?

02 February 2017 0 5K Report

There is a layer of alloy powder subjected to laser sintering. When the temperature reaches above a specified temperature , I need to change properties of that element from powder to sintered product.

A sample code will be helpful

Thanks

Badges
Science topic

More Pranshul Gupta's questions See All

Meshing in APDL

I needed to mesh a cuboid with variable mesh size. In the centre region (2x8x1 mm), I need to have hexahedral elements of 0.05mm and coarse mesh in the outer region. For this, I have made it in...

04 May 2017 4,313 1 View

How to set pop ups during APDL simulation to yes?

There is a do loop and it assigns new values to the variables in each iteration and ANSYS asks for confirmation to overwrite the variables.what can i include in my code to set this automatically...

02 March 2017 5,891 1 View

How to calculate distance of each node from centre of moving laser(in each substep)?

Simulating a moving laser for Laser Sintering processI have used local cylindrical co ordinate system for locating center of laser on powder bed.However the energy distribution in laser spot...

31 December 2016 2,139 2 View

In ANSYS APDL after killing certain elements in the beggining how can i activate them one by one in subsequent load steps?

I tried using ealive in every load step and solvedwhen i ran the animation over time it shows all the activated elements throughout the animation.What i want is that with time elements should come...

07 August 2016 7,486 6 View

Can any one help me with "ealive" and "ekill" in ANSYS APDL?

I need to simulate laser sinteringIf possible can anyone suggest how to use these for the simulation

07 August 2016 4,899 0 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Why does everyone use vs code?

Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...

07 August 2024 7,013 4 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View