Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

Which is the best wavelength to study aerosol optical depth(AOD) related to climate reseach,which criteria must be adopted in choosing the wavelengh?

We are doing a study on impact of aerosol on precipitation. Which satellite data and which wavelength will be the best. or can some one suggest a criteria to be adopted to choose an instrument...

12 February 2021 6,324 3 View

How do we calculate 95% confidence intervals for RMSE?

I have two datasets (measured and modelled). I want to calculate 95% confidence intervals for RMSE. Cany anyone please help me with this? Thank you in advance

04 February 2021 5,439 6 View

Queries regarding the rain flow counting algorithm?

02 February 2021 9,790 2 View

Doubt in DFT geometry preparation?

Hi all, I am trying to perform some ab inito DFT calculations using cp2k code. I have a unit cell of 120 atoms and would like to know how to refine or reduce the number of atoms in the unit cell...

20 January 2021 6,024 3 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

Is it possible to ligate two restriction ends those have no complementary bases?

In my lab,we are trying to construct a control plasmid. So we have to remove the insert gene which has two restriction ends:one is XhoI and other one is Hind III.So after double digestion we want...

01 January 2021 3,271 4 View

Response Surface Methodology?

I'm using 3 different light intensities (constant values 15,30,45 W) for the wastewater treatment of an organic compound and optimizing the parameters (pH, catalyst dose and light intensity)...

31 December 2020 2,377 4 View

What is the impact of Pandemic on the higher education faculty?

Work life Balance, Stress, Anxiety, Effective teaching

28 December 2020 6,201 3 View

Look for Book?

Can anybody give me the following writer book? Helen Deresky "International Management"

26 December 2020 5,109 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View