How to solve "cannot find -ldl" error in CrossCore Embedded Studio 2.8.1?

Hello, Auto generation C code from MATLAB simulink 2016b which is run on CroosCore Embedded Studio 2.8.1, error is occur like "cannot find -ldl". I have created Cross code project and source code...

10 November 2018 8,801 0 View

How does one multiply two different size of matrices?

I am registered two images. For that, I stored images in matrix. Then I found inverse of one matrix which multiply with 1st image matrix. For multiplicaiton, first matrix's column must same with...

08 September 2014 4,364 5 View

What is relation between homography transformation and perspective transformation?

01 January 1970 6,951 0 View

How can add JPEG or ADPCM noise in an image using opencv?

To add aperiodic structure noise in an image, how can I add JPEG or ADPCM noise in an image using opencv?

01 January 1970 2,652 0 View

How to use code to extract FAST, FFME, BRISK, KAZE/AKAZE for opencv 2.4.9/13?

01 January 1970 5,408 0 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

How to find the mode of classified ocean colour images?

Hello, I have classified 10 S3 OLCI images from the same area (althouth not the same size and/or quadrant) and I would like to do a final image using the mode of the pixel of these 10 images. I...

01 March 2021 9,874 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View