Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How can I homogenize this data to make a meta-analysis?

Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...

22 February 2021 1,115 4 View

Research Gate Does it help researches to publicize their scientific work ?

In my opinion, the RG site is useful in solving scientific problems and shows the researcher's ability. Besides, the separation of the H-index from the self-citations and the overall index is an...

22 February 2021 3,894 6 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View